Raypak 1259B Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 52

background image

Electrical Power Connections

Installations must follow these codes:

•

National Electrical Code and any other national,
state, provincial or local codes or regulations hav-
ing jurisdiction.

•

Safety wiring must be NEC Class 1.

•

Heater must be electrically grounded as required
by the NEC.

•

In Canada, CSA C22. 1 C.E.C. Part 1.

The heater is wired for 120 VAC, <12 amps. The volt-
age is indicated on the tie-in leads. Consult the wiring
diagram shipped with the heater in the instruction
packet. The remote tank control stat, thermostat, or
electronic heater control (as applicable) may be con-
nected to the stage selector terminal (See wiring
diagram). 24 VAC is supplied to this connection
through the heater transformer.

DO NOT attach any

voltage to the stage selector terminals.

Before

starting the heater check to ensure proper voltage to
the heater and pump.

Install a separate disconnect means for each load.
Use appropriately sized wire as defined by NEC, CSA
and/or local code. All primary wiring should be 125% of
minimum rating.

If any of the original wire as supplied with the heater
must be replaced, it must be replaced with 105°C wire
or its equivalent.

Field-Connected Controllers

It is strongly recommended that all individually-pow-
ered control modules and the heater should be
supplied from the same power source.

Check the Power Source

NOTE:

Field-supplied isolation relays should be

installed when field-connected controllers are
mounted more than 50 equivalent feet (18 Ga) from
heater.

WARNING:

Using a multi-meter, check the

following voltages at the terminal block inside the
unit. Make sure proper polarity is followed and house
ground is proven. (See Fig. 18.)

CIRCUIT

BREAKER

WHITE

GROUND

BLACK

GREEN

A B

C

Fig. 16: Wiring Connections

Check the power source:

AC = 108 VAC Minimum, 132 VAC MAX
AB = 108 VAC Minimum, 132 VAC MAX
BC = <1 VAC Maximum

If the heater does not have a factory-wired stage con-
troller, it is factory-wired in an on-off configuration with
other stage terminals jumpered.

To field-connect a stage controller, remove factory-
installed jumpers and wire stage controller as shown in
Fig. 19–22.

Making the Electrical Connections

Refer to Fig. 16–22.

1.

Verify that circuit breaker is properly sized by
referring to heater rating plate. A dedicated circuit
breaker should be provided.

2.

Turn off all power to the heater. Verify that power
has been turned off by testing with a multi-meter

Fig. 17: Multi-meter

21

«
...
19
20
21
22
23
...
»

Содержание 1259B





















































Отзывы:

Нет отзывов

Похожие инструкции для 1259B

Бренд: Teba therm Страницы: 12

Бренд: WarmFlow Страницы: 107

Бренд: IDEAL Страницы: 62

GRAND PELLET 100

Бренд: Metal-Fach Страницы: 60

Бренд: HydroTherm Страницы: 24

LED 24MB W TOP-U/I

Бренд: Lamborghini Caloreclima Страницы: 128

Бренд: BRÖTJE Страницы: 168

Бренд: Prestige Страницы: 104

Бренд: Prestige Страницы: 114

BlueHelix ALPHA C

Бренд: ferolli Страницы: 320

Бренд: Burnham Страницы: 12

Бренд: Burnham Страницы: 104

Roca LIDIA 20 GT EM

Бренд: Baxi Страницы: 3

Бренд: Baxi Страницы: 40

Nuvola 3 BS 140 Fi

Бренд: Baxi Страницы: 224

EBE Express Series

Бренд: Ecoboil Страницы: 4

EB Rapid Series

Бренд: Ecoboil Страницы: 4

Бренд: ACV Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды