Raypak 1259B Скачать руководство пользователя страница 22

Страница: 22 / 52

prior to working with any electrical connections or
components.

Observe proper wire colors while making electri-
cal connections. Many electronic controls are
polarity sensitive. Components damaged by
improper electrical installation are not covered by
warranty.

Provide overload protection and a disconnect
means for equipment serviceability as required by
local and state code.

Install heater controls, thermostats, or building
management systems in accordance with the
applicable manufacturers’ instructions.

Conduit should not be used as the earth ground.

Field Wiring Connection

NOTE:

A grounding electrode conductor shall be

used to connect the equipment grounding
conductors, the equipment enclosures, and the
grounded service conductor to the grounding
electrode.

Fig. 18: Wiring Location

DANGER: SHOCK HAZARD

Make sure electrical power to the heater is discon-
nected to avoid potential serious injury or damage to
components.

CAUTION:

Label all wires prior to disconnection

when servicing controls. Wiring errors can cause im-
proper and dangerous operation. Verify proper
operation after servicing.

Fig. 19: On-Off Wiring Connections

Содержание 1259B





















































Результаты поиска

Содержание 1259B

Отзывы:

Похожие инструкции для 1259B

Бренды по названию

Популярные бренды

Raypak 1259B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 1259B

Отзывы:

Похожие инструкции для 1259B

Бренды по названию

Популярные бренды