background image

24

Raymarine S100 Controller

NO DATA

The autopilot is in Track mode and:
• the autopilot is not receiving SeaTalk navigation 
data, or 
• your GPS is receiving a low strength signal, this 
will clear when the signal improves
Note: The autopilot stops adjusting the heading as 
soon as it loses data.

NO GPS COG

The S1000 autopilot is not receiving valid COG data 
from your GPS system. Check the connections and 
that your GPS unit is powered on and setup to 
transmit COG data.

NO GPS FIX

Your GPS is receiving a low strength signal, this will 
clear when the signal improves

NO PILOT

The controller is not receiving data from the autopi-
lot. Check connections and that the autopilot.

OFFCOURSE

This alarm sounds if you have been off course from 
the locked heading for more than 20 seconds. It 
also states if you are to the PORT or STARBOARD of 
the intended heading.

REGISTRATION INCOMPLETE The registration of your new handset cannot be 

completed as the system has detected other hand-
sets in the vicinity.
1. Switch off all other remote handheld units. and 
repeat the registration process.
2. If this error  persists, take your boat to open water 
(with no other vessel within 100 ft) and repeat the 
registration process. 

ROUTE COMPLETE

This sounds on the completion of a track. Press 

PILOT

 to continue on the same heading or 

STANDBY

 for manual control. 

SHIPS BATTERY

The ships battery voltage has dropped below 
acceptable limits, check the charge state of the bat-
tery.

TOO SLOW

Your speed has fallen below 3 knots. You must be 
travelling faster for the pilot to operate

ALARM MESSAGE

POSSIBLE CAUSE and SOLUTION

Содержание E15024



































Отзывы: