Raymar 3460 Скачать руководство пользователя страница 33

Страница: 33 / 171

3460 Fast’R

1-22

If your AccessWay has:

•

Individual telephone cable connectors

, connect cables from

the telephone service outlets to each modem connector.
The upper connector serves:

— Two- and four-wire leased line modems, on

four-wire leased line cards

— Modem A, on dual-modem cards

The lower connector serves:

— Dial-line connections, on four-wire leased line cards
— Modem B, on dual-modem cards.

•

Mass-termination connectors

, you should have two multi-line

cables from the telephone service outlets to the two mass-
termination connectors on the AccessWay rear panel, already
connected.

•

Note

: Mass-termination is not compatible with the two- or

four-wire leased-line/dial-line modem card.
The upper connector serves Modem A on dual-modem cards.
The lower connector serves Modem B on dual-modem cards.

Refer to the

3460 Fast’R Reference Guide

for cable pin-outs.

A modem begins a self-test sequence when power is applied. A
modem indicates test results as follows:

•

Successful completion

: MR LED steady on.

•

A problem

by setting LEDs in one of these ways:

— MR: slowly blinking. TR: on. OH: off. CD: off.
— MR: off. TR: on. OH: on. CD: on.

You can also check self-test completion with Fast’RVu. Select

Status

, then select:

•

EIA

to display DCD, DTR, DSR, CTS, and RTS signal states

•

Device

to display rate and mode parameters that describe the

modem’s current state

Note the LED pattern. Report any problem to Telenetics
Support.

Connect a cable from a computer serial port to the appropriate
Modem DTE connector on the enclosure rear panel.

To configure modems for operation, go on to Chapter 2.

Installing a Modem Card in an AccessWay

(continued)

Step

Action

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 33 / 171

Результаты поиска

Содержание 3460

Отзывы: