Raymar 3460 Скачать руководство пользователя страница 144

Страница: 144 / 171

3460 Fast’R

C-8

The enclosure has one power interface connector.

The off-line configuration (OLC) button is on the front of the modem
card.

Pressing the button makes the modem enter command mode, in which
you can change configuration options in synchronous or leased line
environments.

Network Management Interface Pin-outs

Pin

NM OUT

NM IN

TXD TXD

RXD RXD

RTS

Signal Ground

DCD

Pins not listed here are not used.

Power Interface

Power Type

Connector

Industry Standard

Barrier strip

Changing a Configuration With the OLC Button

Step

Stage

Change one or more configuration options.

Enter the Save to Option Set command (AT&W

, where

is 1 or 2)

Enter the Option Set to Power Up In command (AT&Y

, where

is:

0 for last-loaded option set; 1 for Option Set 1, or 2 for Option Set 2)

Press the OLC button. The modem restarts and powers up using the
selected configuration option set.

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 144 / 171

Результаты поиска

Содержание 3460

Отзывы: