Raymar 3460 Скачать руководство пользователя страница 129

Страница: 129 / 171

3460 Fast’R

B-29

Options Stored in Status (S-) Registers

Some AT command options are stored in status registers.

S-Register Command Cross-Reference

Register

Parameter

Command

(Default

Value)

Description

Ring Count to
Answer On*

ATS0=

(0)

Modem answers a call after ring

Current Ring
Count*

ATS1

(0)

Counts rings (view only)

Escape Code
Character*

ATS2=

(43)

Defines character used to change
from data mode to command
mode.

Return
Character*

ATS3=

(13)

Set command-line termination
character

Line Feed
Character*

ATS4=

(10)

Set response formatting character

Backspace
Character*

ATS5=

(8)

Set command-line editing
character

S6 Wait

For

Dial

Tone ATS6=

(3)

Set duration

Wait For Data
Carrier

(Country-specific
for France only)

ATS7=

AT*DD9

AT*TT5

(30)

Set duration

Dial Wait=S7

Call Timeout=S7

Dial Modifiers

ATS0=

(3)

Set comma character

S10

DCD Loss
Disconnect

ATS10=

(15)

Set delay duration; varies with the
modulation mode:

• V.34, V.32:

— 0=Disabled
— 1-19=Specified sec.
— 20-255=20 sec.

• V.22bis, V.21, B212, B103:

— 0=Disabled
— 1-255=Specified 0.1 sec

*Changed values are not automatically stored to non-volatile memory. To retain changed
values, save them to an option set.

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 129 / 171

Результаты поиска

Содержание 3460

Отзывы: