Raymar 3460 Скачать руководство пользователя страница 115

Страница: 115 / 171

3460 Fast’R

B-15

Secondary Channel

The AT

NE command controls secondary channel

operation. You can enable and disable the secondary
channel through the AT ACU, Fast’RVu (Commands
menu), or an NMS. The option is saved in non-volatile
memory.

For more information, refer to the “Network
Management (AT

NE)” section in Chapter 3.

=On. Enables the secondary channel.

=Off. Disables the secondary channel.

Network Control Override Mode

When this parameter is enabled, a modem ignores
network management commands, except status requests.

When you connect to a modem that has Network
Override enabled, Fast’RVu indicates this with the
orange OR LED in its display.

For more information, refer to the “Network
Management (AT

NE)” section in Chapter 3.

=Off. Disables network management override.

=On. Enables network management override.

AT Command Set

(continued)

Command

Option

Description

The characters

precede all commands except:

+++

#####

, and

Parameters and options shown shaded gray vary by country. For your country’s options,
refer to the

3460 Fast’R Reference Guide

(TEL–T0022).

Default (pre-set) options are underlined.

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 115 / 171

Результаты поиска

Содержание 3460

Отзывы: