background image

The  appliance  can  only  be  installed  in  a  room  which

meets  the  ventilation  regulations  in  force.  But,  in  any

event the room must have a permanent vent of minimum

free air area, see below:

IMPORTANT:  THE  LOUVERED  AIR  INTAKE  AT  THE

BOTTOM  FRONT  OF  THIS  APPLIANCE  MUST  BE

KEPT CLEAR OF ANY OBSTRUCTIONS.

Detailed recommendations for air supply are given in the

Building  Regulations  and  in  BS  5410:  Part  1.  The

following notes are intended to give general guidance.

1.

Combustion and ventilation air supply to oil fired 

appliance has to comply with the Building Regulations

and with BS 5410: Part 1. The air supply requirement

for oil fired appliance in 550mm

2

per kW of maximum

rated output above 5 kW. These requirements are 

illustrated in OFTEC Technical Book No. 3.

2.

The combustion air supply to open flued appliances 

should normally be provided at high level into a room 

where it will not cause discomfort by creating a cold 

draught across the floor.

3.

If combustion air is supplied through an under floor 

duct the grilles at each end should be positioned in the

vertical plane to reduce the risk of blockage. Ducts 

should be sized so as to reduce the resistance to air 

flow.

4.

The ventilation requirement for kitchen in Part F of the

Building Regulations (England & Wales) is for 

mechanical extract at the rate of 60 litres per second 

or 30 litres if the fan is incorporated in a cooker hood.

The amount can be reduced if the spillage of flue 

gases might be caused by the outflow of air from the 

room.

Background ventilation is also required, either by 

producing a constant extract rate of one air change per

hour or by having ventilation openings of not less than

4000m

2

.

5.

Extract fan should be positioned as far away from the

open flue as possible and should have a sufficient 

dedicated air supply. To undertake a test the oil fired 

appliance should be set in operation and the doors and

windows of the room containing it should be closed.

The extract fan should then be run at its maximum 

setting. The oil fired heating appliance should be 

observed to operate satisfactorily both before and after

the fan is switched on.

6.

It is preferable for the air supply for an extract fan to be

located where it can serve the fan without the air 

stream passing close to the oil fired appliance.

7.

Oil fired appliances must not draw the combustion air

from a garage.

Carbon Monoxide Detector/Alarm

It is recommended that a Carbon Monoxide

Detector/Alarm should be fitted in the same area as the

cooker.

13

Site requirements

AIR SUPPLY

680KCD O/F

780KCD O/F

180cm

2

MODEL

MIN. AIR REQUIREMENT

Содержание 680KCD C





































Отзывы: