Raven MPV-7100 Скачать руководство пользователя страница 44

Страница: 44 / 52

RAVEN MPV-7100/7100S OWNER’S MANUAL

PROB LEM

C AUSE

SOLUT I ON

Engine runs erratically

Fuel line blocked.

Clean fuel line/filter.

Dirty or old fuel.

Drain tank. Refill with fresh, clean

gasoline.

Dirty air filter.

Clean/replace air filter.

Spark plug wire loose.

Check and connect wire.

Engine overheats

Air intake screen plugged.

Clean any debris from around cooling

fins and blower housing.

Oil level low.

Check oil, fill with proper amount.

Excessive ethanol in fuel

Drain tank. Refill with fresh gasoline

containing less than 10% ethanol.

Engine clicks but will not start

Weak or dead battery.

Recharge battery.

Damaged wiring.

Check all wiring and replace as

necessary.

Corroded battery terminals.

Clean battery terminals.

Faulty starter.

Call for Service

Excessive Vibration

Worn or bent blade(s).

Replace blade(s).

Loose Blade(s).

Tighten blade or replace blade adapter

set.

Damaged Tires.

Call for Service

Jerky operation on hills or rough terrain Terrain causes operator to bounce on

throttle.

Use Cruise Control for smooth operation.

Uneven cut

Cutting deck not level.

Level mower deck from side to side and

front to rear.

Dull blade(s).

Replace blade(s)

Uneven tire pressure.

Check tire pressure, adjust accordingly

to 15 psi rear, 12 psi front.

Buildup of debris under mower.

Clean underside of mower.

Speed too fast while mowing.

Travel slower.

Poor grass discharge

Discharge chute plugged.

Unplug chute.

Wet grass.

Allow grass to dry before cutting.

Cutting deck not leveled properly.

Level mower deck from side to side and

front to rear.

Uneven tire pressure.

Check tire pressure, adjust accordingly

to 15 psi rear, 12 psi front.

Build up of debris under mower

Clean underside of mower.

Blades improperly installed.

Reinstall blades correctly.

12V Battery will not charge

Blown 30 A fuse.

Replace green 30 A fuse.

Bad/dead battery cell(s).

Replace battery.

Battery terminals dirty.

Clean as necessary.

Headlights not working

Headlight switch is off.

Turn switch on.

Blown 20A (yellow) fuse.

Replace 20A (yellow) fuse.

Engine dies when switching into

reverse

Reverse Mow Override is not “on”

while mower or other attachment is

engaged.

Be sure to engage Reverse Mow

Override correctly. (See page 22).

Patches of grass left uncut

Speed too fast while mowing.

Travel slower.

Cutting deck needs cleaning.

Clean cutting deck.

roubleshootIng

4 4

Содержание MPV-7100





















































Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды

Raven MPV-7100, Руководство владельца и эксплуатации

Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды