Raven MPV-7100 Скачать руководство пользователя страница 19

Страница: 19 / 52

Operating on Electric Only Mode

Select high or Low gear. (See page 17).

Set the drive mode switch to Neutral.

Turn the key in the ignition switch to the position labeled with

the battery icon until it clicks one time.

Step on the brake pedal to release the parking brake.

The MPV will now operate on electricity only. Set drive mode and

use the brake and throttle to travel as normal. (Neither the mowing

deck, nor the generator will function in this mode.)

WWW. RAVENAMERI C A. C OM

peratIon

WARNING!

•

CLEAR THE AREA OF BYSTANDERS BEFORE

OPERATING. IMMEDIATELY STOP MACHINE IF

ANYONE ENTERS THE AREA.

•

NEVER LEAVE A RUNNING MACHINE

UNATTENDED. ALWAYS SET THE PARKING

BRAKE, STOP THE ENGINE, AND REMOVE THE

KEY TO PREVENT UNAUTHORIZED USE.

Before Each Use

Check the MPV

Test safety interlocks. See page 18.

Check tire pressure.

Check fuel level.

Check engine oil level.

Remove grass and debris from engine compartment

and muffler area and on top of mower deck, before and

after operation.

Check area below machine for leaks.

Check the Area around the MPV

For your safety and the safety of others, always check the

area around the MPV before operating. Before driving the

MPV, check for children, pets and inanimate obstacles in

your driving path.

Before mowing with the MPV, check for anything that might

be picked up and thrown by the cutting blades. Check for

sticks, stones and other debris and remove them from the

cutting area. Check the deck cutting height, and ensure the

MPV is in low gear before cutting.

Understanding Basic Operation

Before turning on or operating the MPV you must always:

Be seated in the operator’s chair.

Put the Drive selector in Neutral.

Press the brake or engage the parking brake.

If ANY of these three conditions are not met, the MPV may

not start or operate properly.

Driving

NOTE:

The MPV has a switch to alternate between generate

mode and drive mode. If the switch (located on the

power panel) is in generate mode, the MPV will

NOT move.

NOTE:

Electric only mode will drain the batteries. The

batteries can either be recharged by operating in

Hybrid Mode or with the optional manual battery

charger available as an accessory sold separately.

B r a k e

T h r o t t l e

Содержание MPV-7100





















































Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды

Raven MPV-7100, Руководство владельца и эксплуатации

Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды