Raven MPV-7100 Скачать руководство пользователя страница 13

Страница: 13 / 52

Cruise Control Operation

Disengaging the Cruise Control
a.

Push the brake pedal or push the cruise control button.

Cruise control will no longer be activated.

Setting the Cruise Control
a.

Push the throttle down until you accelerate to the desired

speed.

Hold the throttle at that speed and push the cruise switch.

Release your foot from the pedal to engage cruise control.

Use Cruise Control for a smooth riding experience and to regulate

your speed while in transport and while mowing.

CRUISE ON

CRUISE OFF

Drive Mode Switch

WWW. RAVENAMERI C A. C OM

Drive Mode Switch and Function

The drive mode switch sets the direction of travel between

Forward, Neutral and Reverse.

eatures

Forward

The drive mode switch must be set to Neutral (N)

when starting and parking the MPV.

2 Start the engine, then release the parking brake by

stepping on the brake pedal.

Set the drive mode switch to Forward (FWD).

4 Release the brake pedal and slowly step on the

throttle until the desired speed is achieved.

Reverse

1 If moving, push the brake pedal all the way down to

stop the MPV.

If stationary, ensure the drive mode switch in neutral (N),

then check that the area behind and around the MPV is

clear.

3 While holding the brake pedal down, change the drive

mode switch to Reverse (REV).

4 Slowly press down on the throttle pedal until the

desired speed is achieved.

Содержание MPV-7100





















































Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды

Raven MPV-7100, Руководство владельца и эксплуатации

Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды