29
User’s manual HANDHELD TOUCH RADIO
User’s manual HANDHELD TOUCH RADIO
Pag.38
Pag.39
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
Unscrew the protective cap and press
the button to reset the thermal breaker
PLEASE READ CAREFULLY THE FOLLOWING INSTRUCTIONS TO PERFORM PROPER CLEANING.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY LEAD TO MALFUNCTIONS OF THE STOVE.
Grate
Grate
grid
Housing
In the case of alarm 07 THERMAL BREAKER below shows the location where to operate to reset the thermal switch with
manual reset.
Cleaning should be provided by the user
Before any cleaning operation on the stove, implement the following precautions:
- switch off the stove and disconnect the power cord with the stove in “Switched OFF” state;
- make sure all the parts of the stove are cold;
- make sure the ash is completely cooled.
Unscrew the protective cap and press
the button to reset the thermal breaker
Manual reset thermal breaker
Clean the surfaces
To clean the surfaces of the coated metal parts, use a cloth soaked in water or water and soap.
Attention! Use of abrasive detergents or diluents can damage the surface of the stove.
Grate cleaning should be carried out before each switch on
To ensure proper cleaning before switching on the stove, it is necessary to check that the brazier is clean and so that they are always
excellent combustion, thus avoiding any overheating that may cause changes in the color of the paint or peeling of the door coating.
Furthermore, poor cleaning of the grate can cause stove switch on problems.
Before removing the grate and check for any dirt inside it, remember to remove the “grill grate”.
Once the brazier grill is clean it should be fitted in its housing ALWAYS AFTER having installed the brazier.
Clean basket
Basket that needs cleaning
If you use another type of pellets, even of the same brand, this may lead to differences in combustion that may result in greater ash de-
posits inside the grate. Correct cleaning, carried out on a daily basis, allows the stove to burn pellets omptimally with a good and steady
heating output, preventing malfunctions that over time may call for the intervention of a technician to restore stove’s operation.
Cleaning the ash pan
Remove the drawer from the stove and remove the ash collected using an ash vacuum; be very careful if the grate is still hot as this can
damage the cleaning equipment.
Cleaning operations of the stove depend on the quality of the pellets used and the frequency of use.
It may be necessary to carry out these operations on a daily basis.
Drawer
ash
DO NOT SWITCH ON THE STOVE IF YOU NOTICE ANY DAMAGES ON GLASS SURFACE.
CONTACT THE TECHNICAL SUPPORT SERVICE TO HAVE IT REPLACED.
Manual tube bundle cleaning
(where applicable)
Operate the L-shaped pin forward and backward to keep the tube bundle clean and thus
ensure optimal heat exchange.
Cleaning the internal vermiculite (Firex 600)
Pin to be operated
“Forward/Backward”
Ash pan that needs to be emptied
Cleaning glass
The glass of the door should be cleaned with the stove cooled down using a cotton cloth or paper towel.
Usually, we recommend you clean the glass with a damp (water) cloth and ash collected after burning (having an abrasive function).
The FIREX 600 products stand out due to the fact that they are heat resistant, lightweight and have excellent insulation capacity, with
consequent improvement of combustion and performance of the stove. During combustion, the FIREX 600 whitens due to Pyrolysis, mak-
ing the flame light and bright. Therefore, if combustion is suitably regu-lated, the original colour of the internal part of FIREX 600 remains
unchanged.
This means that the colour of vermiculite during combustion indicates whether the latter is correct or not:
FIREX 600 LIGHT = OPTIMAL COMBUSTION
FIREX 600 DARK = BAD COMBUSTION
Firex 600 does not require any specific maintenance. you must only remove the dust with a brush if you intend to clean the ash built up
during combustion.
- You should not use abrasive sponges to clean the more stubborn residues as it could compromise the thickness of the FIREX 600,
creating critical breaking points.
- It is not advisable to use the vacuum cleaner hose in direct contact with FIREX 600.
- It is not advisable to use damp clothes to clean the FIREX 600.
FIREX 600 is resistant to heat but not to shocks: handle it carefully after removal.
After a few hours of operation FIREX 600 may show slight abrasion: this is absolutely normal, as the flame creates micro-grooves in the
panel, without compromising the latter.
The service life of FIREX 600 depends exclusively on the way in which maintenance is performed.
Pellet door/gate open
