Rattler 200 Скачать руководство пользователя

Страница: 6 / 27

This wire provides a (-) 200 mA output whenever the transmitter code controlling Channel 3 is received. This

output will continue as long as that transmission is received. Use for options such as 551T Valet® Start system,

529T or 530T power window controllers, etc.

IMPORTANT!

Never use this wire to drive anything except a relay or a low-current input! The tran-

sistorized output can only provide 200 mA of current, and connecting directly to a solenoid, motor,
or other high-current device will cause it to fail.

Connect this wire to the optional domelight supervision relay as shown below:

IMPORTANT!

This output is only intended to drive a relay. It cannot be connected directly to the

domelight circuit, as the output cannot support the current draw of one or more light bulbs.

This output is used for progressive door unlock. A progressive unlock system unlocks the driver's door when the

unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again

within 15 seconds after unlocking the driver's door. The BLUE wire outputs a low current (-) pulse on the second

press of the unlock button of the transmitter. This negative unlock output is used to unlock the passenger doors.

H1/6 BLUE (-) 200mA second unlock output

H1/4 BLACK/WHITE (-) domelight supervision relay output

H1/3 WHITE/BLUE (-) channel 3 output

Содержание 200




























Результаты поиска

Содержание 200

Отзывы:

Похожие инструкции для 200

Бренды по названию

Популярные бренды

Rattler 200, Руководство по установке

Результаты поиска

Содержание 200

Отзывы:

Похожие инструкции для 200

Бренды по названию

Популярные бренды