Rattler 200 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 27

background image

© 2000 Directed Electronics, Inc. Vista, CA

5

starter kill harness (H3), 2-pin connector

______

______

primary harness (H1) wire connection guide

This wire supplies (-) ground as long as the system is armed. This output ceases as soon as the system is dis-

armed. This wire can be used to turn on an optional sensor or to ready an optional accessory, such as a pager module.

This wire should be connected to the (+) parking light wire, as described in the

Finding the Wires You Need

section

of this manual. This output is protected with a 10 amp fuse. Never increase the value of the light flash fuse. If

more current is required, use an external relay.

NOTE:

When connecting this wire to a (-) parking light wire, a relay is required. See the following

diagram for the relay application.

H1/2 WHITE (+) light flash output

H1/1 ORANGE (-) ground-when-armed output

BLACK

STARTER KILL OUTPUT

BLACK

STARTER KILL INPUT

H3/1

H3/2

«
...
3
4
5
6
7
...
»

Содержание 200




























Отзывы:

Нет отзывов

Похожие инструкции для 200

Бренд: Nittan Страницы: 18

Бренд: ELRO Страницы: 2

Бренд: Geemarc Страницы: 2

Бренд: IKEA Страницы: 8

CRA54 - Digital Alarm Clock

Бренд: Coby Страницы: 1

Бренд: Naxa Страницы: 16

Бренд: Clas Ohlson Страницы: 2

Бренд: Code Alarm Страницы: 8

Бренд: Directed Electronics Страницы: 10

ST-CVTSD520-WSD-W

Бренд: Security Tronix Страницы: 5

Бренд: Avital Страницы: 39

Бренд: Rattler Страницы: 27

Бренд: Sapling Страницы: 69

Бренд: Quell Страницы: 19

Бренд: Scorpio Страницы: 16

Бренд: Scorpio Страницы: 16

Бренд: Radio Shack Страницы: 8

Бренд: Protec Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды