Rattler 200 Скачать руководство пользователя | Manualshive

Страница: 17 / 27

background image

© 2000 Directed Electronics, Inc. Vista, CA

17

This system is found in Mercedes-Benz and Audi 1985 and newer. The door locks are controlled by an electrically

activated vacuum pump. The control wire will show (+)12V when doors are unlocked and (-) ground when locked.

NOTE:

The system must be programmed for 3.5-second door lock pulses, and the violet jumper

between the #87 lock terminal and the #87 unlock terminal must be cut.

type E: electrically-activated vacuum

«
...
15
16
17
18
19
...
»

Содержание 200




























Отзывы:

Нет отзывов

Похожие инструкции для 200

Бренд: Panasonic Страницы: 2

Бренд: La Crosse Technology Страницы: 10

Бренд: La Crosse Technology Страницы: 6

Бренд: La Crosse Technology Страницы: 8

Бренд: La Crosse Technology Страницы: 5

Бренд: Tyco Electronics Страницы: 100

Бренд: Clifford Страницы: 28

Бренд: First Alert Страницы: 8

Бренд: Kidde Страницы: 2

Бренд: Omega Страницы: 2

Бренд: BRK electronic Страницы: 7

Бренд: La Crosse Technology Страницы: 20

Large Display Alarm Clock

Бренд: Geemarc Страницы: 21

Бренд: Hama Страницы: 19

Бренд: General Monitors Страницы: 72

Бренд: Honeywell Страницы: 5

Notifier VESDA-E VEA Series

Бренд: Honeywell Страницы: 10

Silent Knight SK-Duct

Бренд: Honeywell Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды