Rattler 200 Скачать руководство пользователя

Страница: 25 / 27

You can advance from feature to feature by pressing and releasing the Valet

/Program switch the number of times

necessary to get from the feature you just programmed to the feature you wish to access. For example, if you just

programmed Feature 1 and you want to program Feature 2:

1. Release the Valet

/Program switch.

2. Press and release the Valet/Program switch once to advance from Feature 1 to Feature 2.

3. Press the Valet

/Program switch once more and

HOLD

it.

4. The LED will flash in groups of two and the horn will honk twice (if connected) to confirm that you have

accessed Feature 2.

The learn routine will be exited if:

■

The ignition is turned on.

■

The Valet

/Program switch is pressed too many times.

■

More than 15 seconds elapses between steps.

One long horn honk (if connected) indicates that the Learn Routine has been exited.

features menu

FEATURE

DEFAULT LED ON SETTINGS

LED OFF SETTINGS

NUMBER

(PRESS CHANNEL 1 TRANSMITTER BUTTON) (PRESS CHANNEL 2 TRANSMITTER BUTTON)

Ignition-controlled door locks ON

Ignition-controlled door locks OFF

0.8 second door lock pulse duration

3.5 second door lock pulse duration

Double pulse unlock OFF

Double pulse unlock ON

Security features ON

Security features OFF

Code Hopping ON

Code Hopping OFF

NOTE:

The default settings are indicated in

bold

type.

to exit the learn routine

to access another feature

Содержание 200




























Результаты поиска

Содержание 200

Отзывы:

Похожие инструкции для 200

Бренды по названию

Популярные бренды

Rattler 200, Руководство по установке

Результаты поиска

Содержание 200

Отзывы:

Похожие инструкции для 200

Бренды по названию

Популярные бренды