Rational Combi-Duo 10-2/1 GN Series, Руководство по установке

Страница: 12 / 36

Duo 102G/61Md 05/02
The Combi-Duo kit 10x2/1 GN Gas (spare part no.
6008.1307 and 6008.1308 USA) (see pic. 1/2) consists of:
Pos. Pcs.
Spare part no. Description
1 1 6021.1445 Cover for stiffening plate
2 4 2039.0114 Upper foot part 135 mm
3 1 2770.1329 Vapour deflector
4 1 6021.1444 Flue gas duct (USA 6021.1448)
5 1 6021.1446 Stiffening plate
6 1 5214.1388 Insulation
- 3 2039.0353 Silicone plugs
- 1 5006.0200 Tube of silicone sealant
- 1 Set of fixing materials
The Combi-Duo CleanJet ® accessory set (6008.1316),
see fig. 3, consists of:
Pos. Pcs. Spare part no. Description
7 1 8664.1368 Suction hose set complete
8 1 6021.1550 Connector set, complete
9 1 6021.1553 Hose guide 102 bottom
10 1 6021.1513 Hose guide 102 rear
11 1 6021.1514 Hose guide 102 rear/top
12 1 2765.1510 Hose guide 102 cover
13 2 2062.0338 Plastic Y-joint
14- 4 2066.0533 Hose clip
- 1 Set of fixing materials
12
GB
Lower unit:
• For CleanJet ® units:
a) Pull out cleaning agent/rinse aid tank until it stops
b) Remove connector hoses from the cleaning agent/rinse
aid tank.
c) Remove tank from unit.
- Unscrew the lower part of the foot of the unit pic. 3
- Unscrew the upper part of the foot of the unit using a
17 mm open-ended wrench pic. 3
- Use an M10x30 screw to attach the new top foot section
(pos. 2, length 135 mm) to the device
- Screw in the lower part of the foot of the unit.
• For CleanJet ® units:
a) fix the hose set complete (pos. 8) with two hose clamps
to top of foot, front left, page 8/9 “A”
b) fix the hose guide 102 bottom (pos. 9) with two hose
clamps to top of foot, rear left, page 8/9 “B”
• If the upper unit is also to be fitted with CleanJet ® ,
proceed as follows:
a) Cut the two suction hoses of the complete connector set
(pos. 8) approx. 200 mm behind the connectors.
b) Remove the elbow joints of the unit.
c) Connect the connector hoses of the unit and hoses of
the complete connector set using the Y-joint.
d) Also attach the cut-away hoses of the complete
connector set (used for connecting to the upper unit) to
the Y-joint
page 8/9 “F”
e) Fix hoses with cable ties to the support
f) Position rear hose guide 102 (pos. 10) in place on
ventilation pipe and using M4x10 screws, screw to
bottom hose guide 102
page 8/9 “C”
• If the upper unit is not to be fitted with CleanJet ®
the connector hoses of the complete connector set
can be fitted direct to the pumps. Hoses must then
be shortened to the appropriate length.
- Position the unit and align it using a spirit level pic. 4
- Remove the dome pic. 5
- Clean the cover surface thoroughly
- Using silicone paste, spread a bead around the holes in the
unit cover pic. 5
- Place the cover stiffening plate (pos. 5) in position pic. 6
- Place the insulation (pos. 6) in the recess of the cover
stiffening plate. pic. 7
- Place the cover (pos. 1) on the stiffening plate (the fixing
bracket for the deflector plate must point forward and the
bolts of the stiffening plate must fit through the holes in
the cover).
- Use the silicone to seal the gap between the cover and
stiffening plate.
- Refit the dome again with the distance piece.