11
INITIAL SETTING OF
“FILL” and “EMPTY”
Must be completed during installation to be sure water
reaches level mark on dispenser.
1.
All settings should be done with water source (on
board pressure pump or shore water supply) that
will be used with PURASAN. Settings done will
only be valid for that source, and may need to be
reprogrammed if another source is utilized. Lid
must be closed tight during setting and use.
2.
Dispenser must not contain tablets during initial
set-up. Program “fill” time without tablet to
reach 1/4” below top marked lines, Unplug sen
-
sor cable at Control Module.
3. With power on, press “fill “and count seconds
until water reaches to water level mark on
dispenser. Record seconds as fill. If recorded
seconds are greater than 18 , Open the hole to
approx 1/8” in metering washer between water
valve (221352) and check valve (PX50W) and
repeat.
4. Empty water below tablet dispenser bottom
and entire 3/8” tube till treatment tank while
pressing “empty” button and counting seconds.
Record seconds as empty
5. SET PRELIMINARY “FILL” time:
• Hold the EMPTY & FILL buttons down together
for three seconds. The error LED will give three
quick flashes indicating you have entered pro
-
gram mode - release both buttons.
• Press “FILL “ button as many times as fill
seconds recorded in step 2. example: 8 seconds
press 8 times. Note: maximum is 20 and mini
-
mum is 2.
• Push the “START/STOP” button to store this
value (the unit will flash three times indicating
the time has been set and you have left program
mode).
6. SET PRELIMINARY “EMPTY” time:
• Hold the EMPTY & FILL buttons down together
for three seconds. The error LED will give three
quick flashes indicating you have entered pro
-
gram mode - release both buttons.
• Press “EMPTY “ button as many times as empty
seconds recorded in step 3. Note: maximum is 20
and minimum is 2.
• Push the “START/STOP” button to store this
value (the unit will flash three times indicating
the time has been set and you have left program
mode).
Macerator
PUMP
FIG 11
FILL
EMPTY
ERROR
Treatment
PROGRAMMING
7. TEST SETTINGS:
Without tablets:
Press start/stop button. Water should
fill up in the dispenser at least up to lower line but no
higher than half way between line. Hold time of water
is 20 seconds and not programmable.
After hold time air pump and drain valve will drain
solution. Make sure that water is drained from entire
tube up to treatment tank. Increase empty time using
step 6 if drain time is not sufficient. After drain cycle,
air pump and water solenoid will stay on for 10 more
seconds (non-programmable) to flush check valve
near tank. Repeat flush cycle to check fill time. If
water is not filling up to level between lines, increase
or decrease fill time using steps 2 to 6.
Note: Cycle after drain cycle can be stopped by press
-
ing start/stop button at any time.
With tablets:
Follow start up procedure. Load tablets
and plug sensor cable. If wired to start with toilet:
flush toilet, else press “START/STOP” button, water
should fill up between level line. Make final adjust
-
ment as per above instructions if needed.
Setting of Transfer/macerator pump on time:
Note: Pump time is set to 10 seconds as shipped.
• Hold the EMPTY & FILL buttons down together
for three seconds. The error LED will give three
quick flashes indicating you have entered program
mode - release both buttons.
• Press no discharge button (FIG 11) (next to start
/stop button) as many times as needed set pump
on time.(One push = 1 sec’s, two = 2 sec’s,
three= 3 sec’s etc.) The LED will flash once in
-
dicating a valid key push. Note: Maximum is 20
seconds.
• Push the “START/STOP” button to store this
value (the unit will flash three times indicating
the time has been set and you have left program
mode).
L519 _0815jlc
