Rapid BGC500, Руководство пользователя

Страница: 7 / 136

7
etc.).
8. Do not leave the glue gun unat-
tended while it is switched on.
Protect the glue gun against
heat, e.g. against continuous
sunlight, fire, water, and moistu-
re. There is a risk of explosion.
TECHNICAL SPECIFICATION
Tool Weight (bare-tool) 380 g
Dimensions (bare-tool) 193 x 57 x 231 L*W*H (mm)
Voltage 18 V
Temperature Self-regulated
Glue sticks Rapid Ø12mm
Heat-up time approx. 3 – 4 min
Recommended Battery type Power for all 2.5 Ah, 4.0 Ah, 6.0 Ah
Recommended Charger type Power for all AL1810CV, AL1830CV, AL18V-20
Permitted ambiant temperature
During charge 0 to +35°C
During usage -20 to +50°C
During storage -20 to +50°C
Battery Charging
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely charge
the battery in the battery charger before using your
power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The lithium-ion battery is protected against deep dis-
charging by the “Electronic Cell Protection (ECP)”.
When the battery is empty, the machine is switched
off by means of a protective circuit: The inserted tool
no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
Observe the notes for disposal.
Removing the battery
To remove the battery , press the battery release
button and pull the battery to the rear and out of the
power tool. Do not use force to do this.
2
1
BATTERY RESIDUAL CAPACITY
This indication (C) is made up of four red LEDs
which shows the residual capacity of the inserted
battery. (Figure 1)
The indication is turned on when a battery is inserted
into the tool, or the trigger alone is pressed. Stays on
for 5 seconds.
As the residual capacity in the battery decreases,
less and less LEDs will be turned on.
Once residual capacity is below 6% one LED will
start flashing.
BATTERY ERROR INDICATIONS
If an error in the battery is detected, the LEDs (C)
will instead of residual capacity show the following
indications, and the tool will not operate. (Figure 1)
Battery Error Indications
Error type Battery indicator (Figure 1.C) Solution
Battery
voltage is
critically low
Frist LED flashing
for 10sec
Battery will soon need
charging
Battery is too
warm
All LEDs flashing
for 10sec
Allow the battery to reach
normal temperature
prior use
Battery not
recognized
First and last LEDs
flashing for 10sec
Use a recommended bat-
tery in section “Technical
specification”
Battery information
Battery type Approx. Operating time (min)
2.5 Ah 150
4.0 Ah 270
6.0 Ah 480
FEATURES
1.A. Nozzle
1.B. Power switch
1.C. Battery capacity indicator
2.D. LED Indicator
2.E. Glue feeder
2.F. Stroke adjuster
LED Indicator (Fig 2.D.)
Power Switch Green LED Explanation
OFF OFF Power off
ON Flashing Heating up
ON ON Ready to be used
INTRUCTIONS FOR USE
1. Make sure the battery is charged and connected
to the glue gun.
2. Turn on the power switch.
3. Allow the tool to heat until the green LED stop
flashing. (approx. 3-4 minutes)
4. Insert a glue stick in the back of the tool (Fig 2.E).
5. When the glue gun is fully heated, squeeze the
trigger slowly, until the melted material begins to
flow from the nozzle. Release the trigger to stop
the glue flow.
6. Work with the stroke adjuster and the trigger to
adjust the output and speed of melted glue (Fig
2.F).
7. To change the nozzle, the glue gun should be
slightly warm but turned off. Unscrew the nozzle
using gloves.
8. To prevent the clogging of this glue gun, keep
feeding mechanism and melt chamber free from
dirt and other foreign debris.
2
1
BGX500_User_Manual_20220118.indd 7 BGX500_User_Manual_20220118.indd 7 2022/1/19 ��11:23 2022/1/19 ��11:23