6
etc.).
8. Do not leave the glue gun unat-
tended while it is switched on.
Protect the glue gun against
heat, e.g. against continuous
sunlight, fire, water, and moistu-
re. There is a risk of explosion.
TECHNICAL SPECIFICATION
Tool Weight (bare-tool)
380 g
Dimensions (bare-tool)
193 x 57 x 231 L*W*H (mm)
Voltage
18 V
Temperature
Self-regulated
Glue sticks
Rapid Ø12mm
Heat-up time approx.
3 – 4 min
Recommended Battery type
Power for all 2.5 Ah, 4.0 Ah, 6.0 Ah
Recommended Charger type
Power for all AL1810CV, AL1830CV, AL18V-20
Permitted ambiant temperature
During charge
0 to +35°C
During usage
-20 to +50°C
During storage
-20 to +50°C
Battery Charging
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely charge
the battery in the battery charger before using your
power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The lithium-ion battery is protected against deep dis-
charging by the “Electronic Cell Protection (ECP)”.
When the battery is empty, the machine is switched
off by means of a protective circuit: The inserted tool
no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
Observe the notes for disposal.
Removing the battery
To remove the battery , press the battery release
button and pull the battery to the rear and out of the
power tool. Do not use force to do this.
2
1
BATTERY RESIDUAL CAPACITY
This indication (C) is made up of four red LEDs
which shows the residual capacity of the inserted
battery. (Figure 1)
The indication is turned on when a battery is inserted
into the tool, or the trigger alone is pressed. Stays on
for 5 seconds.
c) Keep the charger away from dirt
and moisture.
d) Always check the charger, cable
and plug before use. Stop using
the charger if you discover any
damage. Do not open the charg-
er yourself, and have it repaired
only by a qualified specialist
using only original replacement
parts. Damaged chargers, ca-
bles and plugs increase the risk
of electric shock.
e) Do not operate the charger on
an easily ignited surface (e.g.
paper, textiles, etc.) or in a
flammable environment. There is
a risk of fire due to the charger
heating up during operation.
f) Rechargeable batteries are to
be removed from the appliance
before being charged.
7) SERVICE
a) Have your power tool serviced
by a qualified repair person
using only identical replacement
parts. This will ensure that the
safety of the power tool is main-
tained.
b) Never service damaged battery
packs. Service of battery packs
should only be performed by
the manufacturer or authorised
service providers.
GLUE GUN SAFETY
WARNINGS
WARNING: This tool must
be placed on its stand
when not in use.
1. This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory and
mental capabilities or lack of ex-
perience and knowledge if they
have been given supervision or
instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
2. Never insert objects other than
Ø12mm Rapid glue sticks into
the machine.
3. Never remove a glue stick that
has already been inserted.
4. It is normal for this tool to beco-
me quite warm during use. This
is normal and does not indicate
a problem.
5. Hot Surfaces: the nozzle of
the appliance and the glue can
reach a temperature of approx.
190°C. Do not touch the heated
nozzle or the hot adhesive. Avoid
any contact with the skin. If you
burn yourself, put the burn in
cold water immediately. Never
try to remove a large quantity of
glue without medical help.
6. Some materials are heat-sen-
sitive and can be damaged by
the hot nozzle or even the hot
glue. Whenever possible, test a
piece of scrap material or a hid-
den portion of the object being
repaired.
7. When you have finished using
the machine, turn the switch off
and wait until it has cooled. Ne-
ver immerse glue gun in water
or other liquids to speed cooling
process. Allow it to air cool only.
The glue gun should be stored
in a closed dry and secure place
(tool box, drawer, cupboard,
1
BGX500_User_Manual_20220118.indd 6
BGX500_User_Manual_20220118.indd 6
2022/1/19 ��11:23
2022/1/19 ��11:23
Содержание BGC500
Страница 128: ...128 e f 4 BGX500_User_Manual_20220118 indd 128 BGX500_User_Manual_20220118 indd 128 2022 1 19 11 23 2022 1 19 11 23...
Страница 134: ...134 BGX500_User_Manual_20220118 indd 134 BGX500_User_Manual_20220118 indd 134 2022 1 19 11 23 2022 1 19 11 23...
Страница 135: ...135 BGX500_User_Manual_20220118 indd 135 BGX500_User_Manual_20220118 indd 135 2022 1 19 11 23 2022 1 19 11 23...