manualshive.com logo in svg
background image

Overview EMI Automotive Band Evaluation 

 

 

01.00

 

Rohde & Schwarz

 EMI Automotive Band Evaluation with R&S©EMC32-K51 

– 1SP07- 

4

 

1

 

Overview EMI Automotive Band Evaluation 

EMI Automotive is the solution for a special measurement task. EMI disturbance 
signals generated from car components have to be measured with on-board 
communication antennas in their frequency bands. The frequency bands as well as the 
bandwidth of the antennas may overlap in the frequency domain. This short description 
shows why the task is not solvable by a standard EMI Scan, EMI Sweep or EMI Auto 
Test template. 
Sequenced definition of frequency sub ranges in hardware setups and Scan/Sweep 
templates cannot overlap. This task is EMC32 Sequencer related. 
EMI Automotive Band Evaluation Test Template now is optimized to generate the 
particular kind of test demanded by the standards with extreme flexibility in 
configuration of the test and the related test report without usage of the EMC32 
Sequencer. 
EMI Automotive Band Evaluation Test Template 

 

defines sub ranges correspondent to the Band related frequency definition and 

 

uses the appropriate antenna specified for this Band per sub range in a 
dedicates hardware setup called Test Setup; 

 

includes a simplified data reduction from auto test to find maxima, and 

 

extends the report to show a separate graphic for each sub range. 

The extension 

“EMI Automotive Band Evaluation” or short “EMI Automotive” therefore 

matches two different demands: 

 

it is closely related to automotive and avionic needs, and 

 

it is a kind of sequencer for EMI Tests. 

The standard applications are on-board EMI measurement sequences in broadband 
and communications frequency bands for automotive and aerospace applications. 

1.1  Test Method 

The tests are intended to provide protection for receivers installed in a vehicle from 
disturbances produced by components/modules in the same vehicle.  
The receiver types to be protected are, for example, broadcast receivers (sound and 
television), land mobile radio, radio telephone, amateur, citizens' radio, Satellite 
Navigation (GPS, etc.) and Bluetooth. The test method is described in CISPR 25 in 
chapter 5: 

“Measurement of emissions received by an antenna on the same vehicle”. 

EMI Automotive Test is based on devices in the Device List and an EMI Automotive 
Test Template. To achieve a maximum in flexibility the test template editor allows all 
kinds of settings and changings which in all other tests are subject to the Hardware-
Setup. EMI Automotive test template works comparable to a test sequence, so it is 
possible to do sub ranges with overlapping frequency ranges. 

1.2  Standards related to EMI Band Evaluation 

CISPR 25: 

“Vehicles, boats and internal combustion engines – Radio disturbance 

characteristics 

– Limits and methods of measurement for the protection of on-board 

receivers

”; Edition 3.0 2008-03. CISPR 25 describes the test method and gives a set of 

limit lines. 

Содержание EMC32













































Отзывы: