R&S EMC32 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 44

R&S EMC32 Скачать руководство пользователя страница 20

Configuration of Test Cases in the Editor

01.00

Rohde & Schwarz

EMI Automotive Band Evaluation with R&S©EMC32-K51

– 1SP07-

20

3.3 Settings in Subrange tab

In the

Subrange

tab, the following parameters can be set:

Figure 21: Settings of the Subrange tab

Table 3-2: Setting in the Subrange tab

Frequency

Start and stop

frequency

for this subrange. The

stop frequency must always be higher than the
start frequency.

Properties

Subrange Name

:

Individual name can be defined here for the
subrange or band

Enabled

:



Checked: Measurement defined in this
subrange will be carried out during test
run,



Unchecked: Measurement defined in this
subrange will be skipped during test run

Detectors

If one or both

detectors

should be used for this

subrange. If only one detector is selected it will
be used for this subrange automatically.

Detector
Mode

Allows to check ClearWrite and / or Maxhold



ClearWrite

: New measurement value

overwrites the old one, and



MaxHold

: New measurement value is

stored if it is higher than the old one

«
...
18
19
20
21
22
...
»

Содержание EMC32













































Отзывы:

Нет отзывов