Page
8
of
18
DG0030
R&G
Unit 1 Shelleys Lane, East Worldham, Alton, Hampshire, GU34 3AQ
•
You can now take the radiator guard and slide this into place ensuring that the
bend in the side profile of the downpipe grille sits snugly into the LHS fairing as
shown in picture 18. Any plastic tabs located inside of the fairing should sit
behind the grille component to hold this firmly in place.
•
Line up the upper downpipe grille mount with the lower radiator mount and
replace the OEM 10mm hex bolt and tighten to the correct torque as shown in
picture 19, (some Loctite or similar may be used to ensure this bolt remains in
place, as access is limited with DG fitted).
•
If fitting with an R&G Radiator Guard in place, ensure the radiator guard lower
mount sits between the downpipe grille mount and radiator mount.
•
Ensure that the lower mount lines up with the lower fairing join as in picture 20.
•
You can now reassemble the fairing in the reverse order as it was removed,
making sure to correctly line up the downpipe grille with the RHS of the fairing as
it is placed back onto the bike. Ensure to reconnect all electrical connections.
•
When the main fairing panel is affixed to the bike, ensure the lower connection
mount holes line up together.
•
At this stage, on the bellypan section of the fairing, locate both sides together
and fit Spacer 1115 (Item 2) into the lower mount with the small boss locating
into the fairing and affix the M5 bolt (item 3) through the spacer, both fairing
mounts and the lower grille mount.
•
This should be fastened with the M5 washer (item 5) and Nyloc nut (item 4) by
using your 10mm socket and extension to access the nut from underneath the
fairing, whilst stopping the bolt (item 3) from turning with your 3mm Allen key as
demonstrated in pictures 21 and 22.
•
Now you can complete the re-fitting of the upper dashboard fairing panels.
•
Ensure the Downpipe Grille is installed correctly and fitted securely.
•
Ensure all panels and bolts are secure and torqued correctly before riding.
ISSUE 1 07/03/2019 (DM)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G
may make design changes which do not diminish their performance or visual appeal and supplying them in
such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to
title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the
Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular
purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care
and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any
defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall
not be liable if the Products have been modified or used or maintained otherwise than in accordance with
R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the
amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the
Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned
direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be
returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns
are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at
time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products,
unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
