background image

UAM4SYS 

• 

12  

 

 

SURFACE MOUNT COMPONENT SOLDERING INSTRUCTIONS: 

 
You’ll notice that the circuit board contains only a few holes for component 
leads to pass through. This is because the SMT components will be affixed to 
the TOP side of the PC board, the side with the white printing. Be aware that 
the component view for assembly is looking at the TOP side of the PC board.  
Patience is the key when installing surface mount components. Typically, the 
first step (after identifying the component) is to “tin” one of the PC traces that 
will connect to the part. Once this is accomplished, the part can be installed by 
holding it with tweezers in contact with the “tinned” trace and re-heating the 
solder (see the following diagrams). Another commonly used technique is to 
glue the surface mount components to the printed circuit board before 
soldering. The procedure is to take a small amount of glue (usually with a pin 
or toothpick) and “dab” the circuit board in the place where the component will 
be affixed. Be careful not to apply too much glue as when the part is placed it 
may “squash” the glue underneath the soldering tabs of the component. 
Carefully place the part into position, and when the glue dries, solder the 
connection.   

 

 
 
 
 
 
 

Содержание UAM4SYS













































Отзывы: