background image

GLOSSARY

CLASSES OF VEHICULAR GATE OPERATORS

VEHICULAR HORIZONTAL SLIDE-GATE OPERATOR  (OR SYSTEM)-

A vehicular gate operator

(or system) that controls a gate which slides in a horizontal direction that is intended for use for
vehicular entrance or exit to a drive, parking lot, or the like.

VEHICULAR SWING-GATE OPERATOR (OR SYSTEM) -

A vehicular gate operator (or system) that

controls a gate which swings in an arc in a horizontal plane that is intended for use for vehicular
entrance or exit to a drive, parking lot or the like.

RESIDENTIAL VEHICULAR GATE OPERATOR-CLASS I 

- A vehicular gate operator (or system)

intended for use in a home of one-to four single family dwellings, or a garage or parking area associ-
ated therewith.

COMMERCIAL/GENERAL ACCESS VEHICULAR GATE OPERATOR- CLASS II

- A vehicular gate

operator (or system) intended for use in an commercial location or building such as a multi-family
housing unit (five or more single family units), hotels, garages, retail stores, or other buildings serv-
ing the general public. 

INDUSTRIAL/LIMITED ACCESS VEHICULAR GATE OPERATOR - CLASS III

- A vehicular gate

operator (or system) intended for use in an industrial location or building such as a factory or loading
dock area or other locations not intended to service the general public.

RESTRICTED ACCESS VEHICULAR GATE OPERATOR - CLASS IV 

- A vehicular gate operator

(or system) intended for use in a guarded industrial location or building such as an airport security
area or other restricted access locations not servicing the general public, in which unauthorized
access is prevented via supervision by security personnel.

V I S I T

V I S I T

O U R   W E B S I T E  

O U R   W E B S I T E  

A

A

T

T

:   W W W

:   W W W

. R A M S E T I N C . C O M

. R A M S E T I N C . C O M

Ramset Automatic Gate Systems 

z

(800) 771-7055 

z

9116 De Garmo Ave. 

z

Sun Valley, CA. 91352

Содержание RAM-30 UL



















Отзывы: