background image

WS-PRO2 Weather Station Manual 
GT 

27176

 

Page 29 of 61 

 
 

4.1.2 Solar Panel Installation 

 

 

 

 

Figure 18

 

 

Mount the solar panel to the tower using the mounting brackets as shown 
in Figure 18.  Mount the solar panel to the tower so it faces south 
(northern hemisphere).  Position it as high off the ground as practical; 
ensuring it cannot interfere with air flow or sunlight around the sensors.  
The solar panel should be oriented to receive maximum insolation over 
the course of the year.  Suggested tilt angles (referenced to the horizontal 
plane) are listed below: 
 
Site Latitude 

Tilt Angle 

0 to 10 degrees 

10 degrees 

11 to 20 

La 5 degrees 

21 to 45 

La 10 degrees 

46 to 65 

La 15 degrees 

>65+ 80 

degrees 

 
After determining the tilt angle, loosen the two bolts that attach the 
mounting bracket to the panel. Adjust the angle, and then tighten the bolts. 
Secure the lead wire to the mast using wire ties as show in Figure 19. 
Connect the plug at the end of the solar panel cable to the connector 
marked “Power”. Make sure the plug is fully seated and the locking ring 
turned clockwise until it stops. 

 

Содержание WS-PRO2

































































Отзывы: