Rain Bird ESP-LXME Скачать руководство пользователя страница 101

Страница: 101 / 116

ESP-LXME Controller

Install the Controller

The ESP-LXME controller mounts to a wall (or suitable mounting

surface).

NOTE:

An optional metal cabinet (LXMM) and pedestal

(LXMMPED) are also available for the ESP-LXME controller. If you

intend to use those options, follow the installation instructions for

those products before installing the controller.

WARNING:

This controller must be installed in compliance with

local electrical codes.

Select Location for Controller

Select a location that:

Is easily accessible

Allows for comfortable viewing

Has a flat wall surface

Near 120 V or 230/240 V AC power source (depending on model)

Is safe from potential vandalism

Is outside the range of operating sprinklers

15 in.

(38,1 cm)

14.32 in.

(36,4 cm)

12.69 in.

(32,2 cm)

Eye Level

Cabinet Depth

5.5 in (14 cm)

Depending on model

120 or 230/240 V AC

wiring in conduit

Field wiring

in conduit

Wall

Grade

Select Controller Location

Содержание ESP-LXME





















































































































Результаты поиска

Содержание ESP-LXME

Отзывы:

Rain Bird ESP-LXME, Инструкция по установке, программированию и эксплуатации, Страница: 101 / 116

Результаты поиска

Содержание ESP-LXME

Отзывы: