background image

P/N R9340-0104                                     37           © 2010 RAILWAY  EQUIPMENT CO. 
REV B 
5/11 

XI. 

   LIMITED 

WARRANTY 

 

 

Railway Equipment Co., Inc. (“Railway”) warrants all of its products to be free  from defects in material and  

                workmanship when used under specified operating conditions and within specified limits.  Railway’s  
                warranty shall extend for a period of two (2) years from the date of shipment to the original purchaser. 
 
 

This warranty is expressly in lieu of and excludes all other expressed or implied warranties, including but not  

                limited to warranties of merchantability and fitness for a particular purpose. 
 
 

Railway, its agents, or representatives shall in no circumstance be liable for any direct, indirect, special,  

                penal, or consequential loss or damage of any nature resulting from the malfunction of the product. 
 
 

Remedies under this warranty are expressly limited to repair or replacement of the product at the sole  

                discretion of Railway. 
 
 

Before returning any defective product to Railway, contact the factory at the address or telephone number at  

                the bottom of this article for a Return  Merchandise Authorization number and instructions as to how and  
                where the return is to be shipped.  Materials received without this authorization will be returned at the  
                customer’s expense.   
 
 

Products returned to Railway under warranty must be shipped freight prepaid, and return freight charges for 

                repaired or replaced products, in or out of warranty, will be at customer’s expense. 
 
 

Railway reserves the right to reject any warranty claim on a product that has been altered by the user or  

                damaged in shipping due to inadequate packaging or mishandling by freight carrier. 
 
 

By returning a product to Railway the owner grants permission to Railway to   open and disassemble the  

                product as required for evaluation.  Railway has the sole responsibility for determining the cause an nature of  
                failure, and Railway’s determination with regard thereto shall be final.  Railway reserves the right to 
 

repair or replace any unit at its sole discretion. 

 
 

A returned product that is found, upon inspection by Railway, to be operational within specification is subject  

                to an inspection and testing fee, regardless of its warranty period. 
 
                Railway’s liability on any claim of any kind (including negligence) for any loss or damage arising out of or  
                resulting from this agreement, or from the performance of breach thereof, of from the products or services 
                furnished hereunder, shall in no case exceed the price of the specific product or service which gives rise to 
                the claim.  All such liability shall terminate upon the expiration of the warranty period of two (2) years, as  
                hereinabove stated. 
 
 

The furnishing of advice or other assistance without separate compensation therefore will not subject Railway  

                to any liability, either in contract, warranty, tort (including negligence) or otherwise. 
 
 

Any alteration or modification of the product, or addition on non-Railway components to the product, unless  

                expressly permitted by Railway in its documentation, will void warranty coverage. 
 
 

This warranty is non-transferable, and warranty coverage is limited to initial user only. 

 
 

Installation and/or use of the product shall demonstrate acceptance of the terms of this warranty. 

 
 

Each of the foregoing paragraphs in this article will apply to the full extent permitted by law.  The invalidity,  

                in whole or part, of any paragraph will not affect the remainder of such paragraph or any other paragraph. 
 

RAILWAY EQUIPMENT CO. 

P.O. Box 68 – Delano, Minnesota 55328  USA 

Tel. (763) 972-2200 Fax (763) 972-2900 

E-Mail - [email protected] 

 
 
  

Содержание 934































































Отзывы: