background image

®

Troubleshooting Proto-Sound 2.0 Problems

Although Proto-Sound® 2.0 has been designed and engineered for ease of  use,
 you may have some questions during initial operation.  The following table
 should answer most questions.  If your problem cannot be resolved with this 
table, contact M.T.H. for assistance (www.mth-railking.com, e-mail: parts@mth-
railking.com,Fax:  410-423-0009, Phone: 410-381-2500, Mail: 7020 Columbia 
Gateway Drive, Columbia MD 21046-1532, ). 

RailKing R142 5-Car Subway Set

18

Starting Up

Bell

Remedy

Remedy

When I press the horn button, the bell comes on 
instead.
I can't get any sound to play when I press the horn 
button.

When I press the bell button, I get a station stop 
announcement, not the bell.

You are holding the bell button too long.  Press it for only 
about one second to trigger the bell.

That is normal for this model.

You may be pressing the button too quickly to trigger the 
bell.  Try pressing the horn button more slowly, taking 
approximately one full second to fully depress the button.

Platform Action Sounds

Remedy

Sometimes the Platform Action Sounds don't play.

Platform Action Sounds play only in neutral at random 
intervals.

Lock-out

Remedy

I can't get the engine to run after I power up the 
transformer.  It sits still with the diesel and 
compressor sounds running.
The engine won't lock into forward, neutral, or 
reverse.

The engine is locked into the neutral position.  Follow the 
procedure in the "Lock into a Direction" section.

Engine speed must be below 10 scale mph (approx. 10 
volts or less in conventional mode).  

Volume

Remedy

The sounds seem distorted, especially when the 
bell is activated.

No Sound

Proto-Sound 2.0 volume is set too high.  Turn the volume 
control knob on the bottom of the chassis counter-
clockwise to reduce the volume.
Volume is set too low, adjust volume control knob on the 
bottom of the chassis clockwise to increase the volume 
or check connector to speaker.

Battery

Remedy

The engine will not leave the initial neutral setting.

I get no sounds when the engine shifts between 
directions. 
After I turn off my transformer, my engine 
continues to make sounds before quitting.

Check to be sure the battery is installed and fully charged.  
See the "Self-Charging Battery Back-Up" section.
The battery may be dead or need to be charged.  See the 
"Self-Charging Battery Back-Up" section.
Proto-Sound 2.0 is designed to continue to sound for a 
few seconds after power to the track has been shut off to 
allow for a more realistic shut-down.

TAS

Remedy

The TAS sounds occasionally repeat themselves.

Proto-Sound 2.0 has a built-in random number generator 
that randomly selects each sound clip to play.  Because 
there are a limited number of sound clips available in 
each TAS sequence, it is probable that some of these 
sound clips will be repeated from time to time.

Содержание R142 5






















Отзывы: