Raider RDP-ID27, Руководство пользователя

Страница: 14 / 64

14 www.raider.bg
allows to work with different speed of spindle.
Alignment is done using the position (2). In the
range of each setting a speed can be adjusted
smoothly by increasing speed and reducing
pressure on the trigger button (1). Turn right
speed regulator (2) leads to increase their
rotation and left to decrease.
8.7. Correct choice of the rate of speed
shall be held where drill is included without
load. So speed-minded when working with a
load may be lower.
8.8. Hammer drilling.
Place the switch (6) the symbol “hammer
drilling.” Switch (6) falls in the correct
position with a distinct twinge.
8.9. Tools to develop or cornering.
Turntable working instrument can be
bent. After continuous operation with low-
speed power to cool as to leave it idling for
approximately 3 minutes with a maximum
speed of rotation. When working with
terminals must always use a universal
extension. Use only the cores that are suitable
for heads of screws. Turning to always place
the switch “drilling / hammer drilling» (6) in
position «Drilling».
8.10. Select the direction of rotation. With
the switch (4) you can change the direction
of rotation of power. Rotate right: For drilling
and turning the screw press to switch the
direction of rotation (4) at point blank range
left. Rotate left: To develop the screws and
nuts, press switch direction of rotation (4)
right to the point blank range. Switch (6) the
choice of operation should be in position
«Drilling». It must be done to change the
direction of rotation when the spindle rotates
a drill!
8.11. Not used in rotation to the left mode
of attack.
8.12. When you need to vent large
diameter, is recommended first to break a
small opening, which will then be drilling to
the desired size. This will prevent overloading
the drill. Drilling deep holes should be done
gradually, as periodically removed from
the drill hole to remove chips or dust. If
during drilling to drill block up in holes,
you should exclude drill. Use a change of
direction of rotation to remove the drill from
the hole. Drill must be kept in alignment
with the hole. Ideally, the drill should be
placed perpendicular to the surface of the
material being processed. If the condition for
perpendicularity is not respected at work can
lead to trapped or breakage in drill hole and
injury to the user. Continued drilling at low
speed the engine from overheating threatens.
Must make periodic breaks during work or to
allow the drill to work on no-load maximum
speed for about 3 minutes. Do not obscure
the openings in the hull used for ventilation
of the engine.
8.13. Outdoor use.
Connect the machine only in installations
equipped with electric switch Fi (safety shut-
off switch with Residual protection RCD
Residual Current Device. RCD must be no
more than 30 mA).
Make periodic breaks at work.
Keep and refer to the accessories carefully.
Do not throw the tool, do not overload, do
not soak in water and other liquids do not use
it for mixing adhesives and concrete coatings.
9. Service and support.
9.1. Impact drill does not require additional
lubrication or special maintenance. There
are no parts requiring maintenance by the
user. Never use water or any liquid chemical
cleaning drill. It should only be wiped with a
piece of dry tissue. Should always be stored
in a dry place and ventilation holes in the
body of the drill to be free.
9.2. Replacing carbon brushes.
Worn-out (shorter than 5 mm), up or broken
engine carbon brushes should be replaced.
Always replace both brushes simultaneously.
Work on replacement of carbon brushes
entrusted only to qualified person with
original spare parts in service
9.3. The repair of your power is best carried
out only by qualified specialists, which used
only original spare parts. This ensures their
safety operation.
10. Environmental protection.
In view of environmental protection
electrical appliances, additional accessories
and packing must be subject to appropriate
processing for reuse of the compound
materials.