Raider RDP-ID27, Руководство пользователя

Страница: 13 / 64

13
and securely than if you hold it by hand.
5.13. Keep your workplace clean.
Mixtures of different materials are
particularly hazardous. Fine shavings from
light metals can be self ignite or explode.
5.14. Do not use the impact drill, where the
power cord is damaged. If during operation the
cable is damaged, do not touch. Immediately
disconnect the plug from the outlet.
Damaged power cables increase the risk
of electric shock.
Failure of the considered instructions may
lead to electric shock, fire and / or severe
injuries.
6. Functional description and purpose of
the impact drill.
Impact drills are in Class II insulation. They
are powered by a collector single-phase motor.
The speed of revolutions is reduced by means
of gear. This kind of power is widely used for
boring holes in wood, dendroid materials,
metal, ceramics and synthetic materials in
the working mode without impackt, as well
as concrete, brick and similar materials in the
operating mode of attack. Power electronic
controls for right and left direction of rotation
can be used to develop cornering or screw
joints. The areas of use are carrying out repair
and construction, carpentry and other work-
related self-amateur activity. Not permitted
the use of power tools for activities other than
its intended purpose.
7. Information on noise and vibration
emitted.
The values are measured according to EN
ISO 3744:2010. A level of noise generated
is generally: the sound pressure level LpA
75 dB (A); sound power LwA 86 dB (A).
Uncertainty K = 3 dB. Work with a earmuffs!
The resultant value of vibration (the vector
sum of the three directions) is determined
according to EN 60745: Drilling in metal: the
value of the emitted vibrations a
h
= 2.30 m/
s
2
, uncertainty K = 1,5 m/s
2
, hammer drilling
in concrete: value the emitted vibrations a
h
=
8.12 m/s
2
, uncertainty K = 1.5 m/s
2
, cornering
/ development: the value of the emitted
vibrations a
h
<2,5 m/s
2
, uncertainty K = 1,5 m/s
2
.
That in this operating manual for the vibration
value is measured by the method specified
in EN 60745 and can be used to compare
different power. The level of vibration varies
depending on the specific activity carried out
and in some cases may exceed that amount in
that direction. If power is used for a long time
in this mode, the load caused by vibration,
could be underestimated. Directions: For an
exact estimate of the burden of vibrations in
a working cycle should be recorded and the
intervals in which the power is off or idling.
This can significantly reduce the reporting
burden of vibrations throughout the business
cycle.
8. Preparing for the job. Installation of
accessories and auxiliary tools.
8.1.1. Auxiliary handle.
Use only the impact drill fitted with an
auxiliary handle (8). You can insert auxiliary
handle (8) in practically any position, to
ensure your comfortable and safe position
for the job. Turn the handle itself (8) axis and
counterclockwise, thus reducing the firmness
of the loop around the head of the drill and
you can rotate the auxiliary handle in the
desired position. Then tighten the grip again
(8), such as turning it clockwise.
8.2. Setting the depth of drilling. With deep
baffle (5) can be pre-set depth of drilling. Pull
the baffle so deep that the distance along the
axis between the tip of the drill and deep baffle
is equal to the desired depth of the hole.
8.3. Placing the drill in the chuck. Turn off
the power of power. Put the key in one of the
open side of the chuck. Dissolving the jaws to
the desired size and place in the drill chuck.
With key-locking in three successive drill a
hole in the chuck. We must always remember
that the key should be removed from the drill
after the completion of operations related to
installation and dismantling of the drill. When
mounting a new drill should be checked by
the inclusion of a short drill, drill that rotates
in an axis without “flicker”. This will help us
make sure that it is not distorted.
8.4. Inclusion and exclusion. Beware of the
voltage of supply network! Supply voltage
of the network must conform to the details
shown on the plate of power. Appliances
marked with 230 V, can be supplied with a
voltage of 220 V.
8.5. To turn the drill press and hold the
trigger switch (1). For locking of the starting
switch pressed (1) press (3). Exclusion
relax power trigger switch (1), respectively,
if anchored to the button (3), first press the
short term and then release the trigger switch
(1).
8.6. Adjust the speed of rotation. Drill