Raider RD-ES47, Руководство пользователя

Страница: 12 / 64

12 www.raider.bg
switch (6) and then release it.
9.2. Adjusting the Speed.
The speed of the switched on power tool
can be variably adjusted, depending on how
far the On/Off switch (6) is pressed. Light
pressure on the On/Off switch (6) results in a
low rotational speed. Further pressure on the
switch results in an increase in speed.
Тhe speed can also be smoothly adjusted
by increasing or decreasing of pressure on
the switch button (6).
9.3. The right choice of the speed is when
screwdriver is included without load. Preset
speed when handling loads may be lower.
9.4. Reversing the rotational direction.
The rotational direction switch (7) is used
to reverse the rotational direction of the
machine. However, this is not possible with
the On/Off switch (6) actuated. Right rotation:
For driving in screws, push the rotational
direction switch (7) left to the stop. Left
rotation: Push the rotational direction switch
(7) right to the stop (for unscrewing screws).
9.5. Screwing depth control.
With screwing-depth control (2) you can
set up the depth of the screw head sinking
into material.
Depth of the screw head of the screw in
the workpiece can be controlled at 24 degrees
for one revolution. Each level corresponds
to the change of depth to 0,0625mm. Rotate
the depth of the regulator (2) in one full turn,
changes the depth of screwing with 1,5 mm.
Turning screwing-depth control (2)
clockwise – decreases the screwing depth.
Turning counter-clockwise, increases the
screwing depth.
It is best to set correct screwing depth by
test screwing in waste material.
10. Working with drywall screwdriver.
10.1. Insert bit in the head of electric
drywall screwdriver. Screwdriver shaft should
not rotate. Press the tip of the screw firmly
to detail, which will wrap and press trigger
switch (6). Screw is wound in detail until a
pre-determined depth, while the stop bushing
(1) touches the surface of the workpiece.
Drive the shaft is interrupted by the clutch
and he stops spinning. Check the depth of
turning the screws and adjust it if necessary.
10.2. To unscrew put to switch direction
of rotation (7) in position “turning left” and
remove screwing depth limiter (1) by pulling
it forward, together with the regulator (2)
without it turning. You can work with put
screwing depth limiter (1), if you change the
depth properly.
For ease of use, screwdriver has clip for
hanging on the belt. With the belt clip, the
machine can be hung onto a belt. The user
has both hands free and the machine is
always at hand.
Do not throw the power tool and do not
overload.
Keep and refer to the accessories carefully.
Make periodic breaks at work.
11. Service and Support. Before any work
on the machine itself, pull the mains plug.
11.1. Never use water or any liquid
chemical for cleaning drywall screwdriver. It
should be cleaned with a piece of dry cloth
and remove the accumulated dust with a
soft brush. Always keep drywall screwdriver
in a dry place and keep the machine and
ventilation slots clean.
11.2. Replacing the carbon brushes. Worn-
out (shorter than 5 mm), or broken carbon
brushes of the engine should be replaced.
Always replace both the two brushes. Work
on replacement of carbon brushes entrusted
only to qualified specialists with original
spare parts in service of RAIDER.
11.3. The repair of your power tool is best
carried out only by qualified specialists in
service RAIDER, which used only original
spare parts. Thus ensuring their safe
operation.
12. Preservation of the environment.
In view of environmental
power, additional accessories and
packaging must be subjected to
appropriate processing for reuse of
the information contained in these
materials.
Do not dispose of electric household
waste! Under the EU Directive 2012/19/EC
on waste electrical and electronic devices
and validation and as a national law power
which can be used more, must be collected
separately and be subjected to appropriate
processing for recovery of contained they
scrap.