background image

 

© 2015 Radiodetection Ltd 

 

45 

Section 13 - iLOC

™ 

 

iLOC is a standard feature of all RD8100 locator models. 
iLOC lets  you control a Bluetooth transmitter (Tx-5B or 
Tx-10B models) remotely using your locator. With iLOC 
you can adjust the output frequency, power settings and 
use  SideStep.  iLOC  commands  are  sent  over  a 
Bluetooth module that can operate at distances of up to 
450m / 1400ft in direct line of sight. 

To use iLOC, the transmitter and locator must be paired 
using the procedure described in Section 5.3. 

NOTE: Operating in built up areas and in areas with high 
electromagnetic  interference  may  reduce  iLOC’s 
performance. 

13.1 Using iLOC 

Locator  and  transmitter  need  to  be  switched  ON  and 
paired to use iLOC. 

For optimum performance: 

 

Minimize obstructions in line of sight 

 

Raise the transmitter off the ground by 30-60cm (1-
2ft) 

 

Point  the  screen  of  the  locator  towards  the 
transmitter 

 

Figure 13.1 Using iLOC 

NOTE:  If  any  iLOC  commands  fail,  move  closer  to  the 
transmitter and repeat the process. 

 

13.2 iLOC functions 

Changing frequencies 

Once the transmitter and the locator are paired, you can 
change  the  transmitter’s  output  frequency  remotely 
using the locator: 

1   On  the  locator,  select  the  frequency  you  want  by 

pressing the 

 key until the frequency is displayed 

on screen. 

2   iLOC commands are sent using the 

 key, press it 

to send the new frequency to the transmitter. 

3  

The  locator’s  LCD  will  display 

SEND

  momentarily 

and then 

OK

 if the transfer is successful. 

4   If the transfer is unsuccessful, the LCD  will display 

an error code. Refer to table 13.1 for a list of codes 
and their meaning. 

If the process fails, you may be out of range or there may 
be  an  error  in  the  connection.  Move  closer  to  the 
transmitter  and  retry  the  procedure.  If  the  connection 
continues to fail, return to the transmitter and reset the 
connection using the procedure described in Section 11. 

NOTE: If  you are locating  a sonde frequency, an iLOC 
command  to  a  paired  transmitter  will  automatically  set 
that transmitter to standby to eliminate interference rom 
the transmitter.  

Adjusting power 

iLOC  lets  you  adjust  the  transmitter’s  power  output 
remotely;  you can  also  put the transmitter  into standby 
mode and then wake it remotely. 

To adjust the power output: 

1   Transmitter power options are located in the 

TXOUT

 

menu on the locator. Press and hold the 

 key to 

display the TXOUT menu 

2   Press the 

 key to enter the TXOUT menu 

3   Scroll up or down through the power output options; 

these are: 

 

STDBY

:  Transmitter  standby  mode,  the 

connection  is  still  active  but  the  output  is 
disabled 

 

LOW

: Low power output 

 

MED

: Medium power output 

 

HIGH

: High power output 

 

BOOST

:  Temporarily  boosts  transmitter  power 

output to its maximum level 

Содержание RD8100























































Отзывы: