background image

Radiocrafts

Embedded Wireless Solutions

       RCxxxxHP-DK

 

 

 
 
 

2020 Radiocrafts AS 

     RCxxxxHP-DK User Manual (rev. 3.04) 

Page 13 of 13 

 

Document Revision History 

Document Revision 

Changes 

1.0 

First release 

1.1 

Updated with RC1700HP info 

1.11 

Updated with TinyMesh info (-TM) 

3.01 

Updated with SIGFOX info, 

3.02 

Updated link to schematics 
Added chapter “Known Issues” 

3.03 

Updated with WIZE info 

3.04 

Added mechanical dimensions of the Development Board. Removed USB in 
product name, kit and board are referred to as a Development Kit / Board. 

 
 

Disclaimer

 

Radiocrafts AS believes the information contained herein is correct and accurate at the time of this printing. However, 
Radiocrafts AS reserves the right to make changes to this product without notice. Radiocrafts AS does not assume 
any responsibility for the use of the described product; neither does it convey any license under its patent rights, or 
the rights of others. The latest updates are available at the Radiocrafts website or by contacting Radiocrafts directly. 
 
As far as possible, major changes of product specifications and functionality will be stated in product specific Errata 
Notes  published  at  the  Radiocrafts  website.  Customers  are  encouraged  to  check  regularly  for  the  most  recent 
updates on products and support tools. 

 

Trademarks

 

RC232™ is a trademark of Radiocrafts AS. The RC232™ Embedded RF Protocol is used in a range of products from 
Radiocrafts. The protocol handles host communication, data buffering, error check, addressing and broadcasting. It 
supports point-to-point, point-to-multipoint and peer-to-peer network topologies. 
TinyMesh™ is a trademark of Tiny Mesh AS. The TinyMesh™ Embedded RF Protocol is used in a range of products 
from Radiocrafts. The protocol handles host communication, data buffering, error check, addressing and 
broadcasting. It supports transparent and packet-addressed mesh topologies. 
 
All other trademarks, registered trademarks and product names are the sole property of their respective owners. 

 

Life Support Policy 

This  Radiocrafts  product  is  not  designed  for  use  in  life  support  appliances,  devices,  or  other  systems  where 
malfunction can reasonably be expected to result in significant personal injury to the user, or as a critical component 
in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the 
life support device or system, or to affect its safety or effectiveness. Radiocrafts AS customers using or selling these 
products  for  use  in  such  applications  do  so  at  their  own  risk  and  agree  to  fully  indemnify  Radiocrafts  AS  for  any 
damages resulting from any improper use or sale. 
 

© 2011-2020, Radiocrafts AS. All rights reserved. 
 
 

Contact Information 

Web site: www.radiocrafts.com 
 
Address: 

Radiocrafts AS

 

Sandakerveien 64 
NO-0484 OSLO 
NORWAY 
 
Tel:  +47 4000 5195 
Fax: +47 22 71 29 15 
E-mails: 

[email protected]

 

[email protected]

 

 

Содержание RC HP-DK Series














Отзывы: