background image

15

EN

12

(10)

(8)

(9)

(5)

10

11

1. 

Measure the distance between the adapter 

(10)

 and 

the rear third of the catch 

(8)

 and mark this distance 

on the precision tube.

i

  Please only use precision tubes 

made from aluminium.

 

‹

The following steps can be left out 
when using octagonal steel shafts.

ALUMINIUM

7.9  Preparation for use of the precision tubes 

7.8  Sliding the tubular motor (9) into the winding shaft

  ATTENTION!

Inserting the tubular motor 
(9) forcibly into the winding  
shaft (5) will cause serious 
damage.

 

‹

Never knock the tubular 
motor 

(9) 

with force into  

the winding shaft 

(5)

1. 

First slide the catch 

(8)

 into the winding shaft 

(5)

.

i

  The motor 

(9)

 must have sufficient free 

space for winding shafts with internal felt.

2. 

Subsequently, press the winding shaft 

(5) 

fully 

onto the adapter 

(10)

.

  ATTENTION!

 

‹

In doing so, ensure that the adapter 

(10)

 does 

not slip off the magnetic ring 

(18)

 on the drive 

head 

(12)

 during the assembly process. Other-

wise malfunctions may occur, see page 26. 

 

‹

The motor must always be pushed fully into 
the winding shaft. The length compensation or 
correction is set with the position of the roller 
capsule, see page 18.

Содержание RolloTube M-line

































Отзывы: