Rabbit 2000, Руководство по началу работы

Страница: 15 / 54

Getting Started Manual 11
2.3.1 Attach BL1810 to Prototyping Board
To attach the BL1810 to the Prototyping Board, turn the BL1810 over so that the battery is
facing up. Plug the pins from headers J4 and J5 on the bottom side of the BL1810 into the
header sockets at J2 and J6 on the Prototyping Board as indicated in Figure 2.
Figure 2. Attach BL1810 to Prototyping Board
NOTE: It is important that you line up the pins on headers J4 and J5 of the BL1810
exactly with the corresponding pins of header sockets J2 and J6 on the Prototyping
Board. The header pins may become bent or damaged if the pin alignment is offset, and
the BL1810 might not work. Permanent electrical damage to the BL1810 board may
also result if a misaligned BL1810 is powered up.
Press the BL1810’s pins firmly into the Prototyping Board headers.
+
S5 RESET
DS1
DS6
DS7
DS8
PWR
R3
Buzzer
DS2
DS3
DS4
DS5
S1
S2
S3
S4
JACKRABBIT PROTOTYPING BOARD
VCC RXB
TXB PC0 PC2 PC4 PC6 AD0 DA0 PD0 PD2 PD4 PD6
GND 485–
VCC SM0
IOBEN
GND /RST
GND RXC TXC PC1 PC3 PC5 PC7 AGND DA1 PD1 PD3 PD5 PD7 GND 485+ VCC SM1 S
TAT
VBA
T
GND
Z-World, Inc.
GND
PA
0
PA
2
PA
4
PA
6
GND
PB0 PB2 PB4 PB6
WDO
GND
PE6 PE4 PE2 PE0 HV0 HV2
K
GND
VCC PA
1
PA
3
PA
5
PA
7
GND PB1 PB3 PB5 PB7 PCLK PE7 PE5 PE3 PE1 GND HV1 HV3 +RA
W
VCC
DS1 DS2 DS3 DS4 DS5 DS6 DS7 DS8
S1 S2 S3 S4
GND
PA
0
PA
1
PA
2
PA
3
PA
4
PA
5
PA
6
PA
7
PB2 PB3 PB4 PB5 GND
J2
J6
Prototyping
Board
J2
J6
Battery
J5
BL1810
GND PA
0
PA
2
PA
4
PA
6
GND PB0 PB2 PB4 PB6 WDO GND PE6 PE4 PE2 PE0 HV0 HV2 K GND
VCC
PA
1
PA
3
PA
5
PA
7
GND
PB1 PB3 PB5 PB7
PCLK
PE7 PE5 PE3 PE1
GND
HV1 HV3
+RA
W
VCC
GND RXC
TXC PC1 PC3 PC5 PC7
AGND
DA1 PD1 PD3 PD5 PD7
GND
485+
VCC
SM1
S
TAT
VBA
T
GND
VCC RXB TXB PC0 PC2 PC4 PC6 AD0 DA0 PD0 PD2 PD4 PD6 GND 485– VCC SM0 IOBEN GND /RST
J4
Downloaded from Elcodis.com electronic components distributor