RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
ADJUSTABLE CONTROL PARAMETERS
(Continued)
SETTING MOTION DETECTION SENSITIVITY
(factory default setting is ideal for most applications)
Trimpot
1.
Hold push button for approx. 3 seconds to enter test mode
2.
Adjust the Time Delay trimpot to the hard stop setting for the
desired sensitivity (options: 5 or 10 min = Low; 15 or 20 min =
Med; 30 min = Max; default Max)
3.
Hold push button for approx. 3 seconds to exit test mode
4.
Return Time Delay to desired setting
WSREM Remote
1. Aim the remote at the IR receiver on the sensor
2. Select “New Settings” and “Sensitivity”
3. 3. Choose from the options of Low, Med or Max
4. 4. Select “Send”; remote displays “Settings Received”
SETTING LIGHT LEVEL HOLD-OFF
Adjust during daylight hours when ambient light is at the
desired level.
Trimpot
Adjust the trimpot on the sensor housing to desired photocell
setting (analog wheel with hashmarks: 1-300fc; default 300fc).
WSREM Remote
1. Aim the remote at the IR receiver on the sensor
2. Select “Adjust Photocell Setting”
3. Choose from the range of 1fc - 300fc with 1 footcandle
increments
4. Select “Send”; remote displays “Settings Received”
The light level values referenced are approximate and reference
4000K CCT. Variations in color temperature may affect the actual
levels the sensor sees. It is recommended that light level hold off
be set up in the morning for best results.
Notes:
Any adjustments made will override any previous settings
whether manually made on the sensor or through the WSREM
commission tool. Adjusting Time Delay does not affect Sensitivity
and vice versa.
PUSH BUTTON FUNCTIONS
The following functions are available via the Push Button.
Manual Mode:
To toggle the unit in or out of Manual Mode,
quickly press the Push Button to toggle the load ON or OFF.
When the load is turned ON manually, it will remain ON as long
as motion is detected and the time delay has not expired. If the
load is turned
OFF manually, the sensor holds the load OFF for as long as
motion is detected and then for an additional 5 minutes of no
motion detection. The next time the sensor detects occupancy,
and the ambient light is lower than the established light level,
the sensor automatically turns ON the load.
Test Mode:
To place the unit in a 10 minute Test Mode, press the
Push Button for about 3 seconds, or enable the Test Mode with
the WSREM. The LED will flash once confirming you are in Test
Mode. To exit Test Mode, press and hold the Push Button for 3
seconds. Walk-test the unit to ensure proper detection.
Service Mode:
To toggle the unit in or out of Service Mode,
press and hold the Push Button for about 6 seconds. The LED
will flash twice confirming you are in or out of Service Mode. In
Service Mode, the LED and load will always be ON.
Power Up On Mode:
Press and hold the Push Button for about
9 seconds to enable Power Up ON Mode. The LED will flash
three times confirming Power Up ON is enabled. In this mode,
the sensor will turn the connected loads ON upon restoration of
power.
Power Up Off Mode:
Press and hold the Push Button for about
12 seconds to enable Power Up OFF Mode. The LED will flash
four times confirming Power Up OFF is enabled. In this mode,
the sensor will keep the connected loads OFF upon restoration
of power. The sensor is set to this mode by default.
Factory Default:
To manually return the unit to factory default
settings, press and hold the Push Button for about 15 seconds.
This will return all settings to factory default with the exception
of time delay and light level, which will be set to the current
trimpot settings. When using the WSREM remote to return
to factory default, all settings will be returned to the original
factory settings regardless of current trimpot positions.
The LED will remain solid ON confirming it has been reset to the
factory default.
Cancel:
To prevent any changes from being made, hold the
push button for about 18 seconds. For example, if resetting to
factory default (or any other setting) is not desired then keep
holding until you reach 18 or more seconds. The LED will turn
off after 18 seconds to indicate there were no changes made.
INSTRUCTIONS
HIGH/LOW BAY PASSIVE INFRARED OCCUPANCY AND DAYLIGHT SENSOR
