R.P.S. Corporation 290 Series, Инструкция по эксплуатации и каталог запасных частей

Страница: 19 / 53

19
290/350 Operator and Parts Manual V13.1210
CENTRAL COMMAND II; V.2 SYSTEM DIAGNOSTICS
Code Probable Cause Service Action
0003
0100
0204
0705
0706
0810
0811
0812
0813
0814
0815
0816
0817
0818
0A01 Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
0B0B Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
1310 Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
1500
1501
1507
1600
Voltage exceeds maximum Can be caused by poor or corroded connections to the batteries or a battery charger being connected.
1704
1705
1706
1800
1802
1B20
1B21
1D02
Tiller settings updated in programming Cycle the power via the keyswitch
1E03
1E04
2102
2103
2C00
2C01
2C02
Dependent on programming Recharge batteries immediately
2D01 Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
2F01 Throttle in drive position during switch on
Incorrect operation of machine. Otherwise check the mechanical condition of the throttle mechanism. Otherwise check for
wiring short circuits on the 20 way connector on the Trio, the 16 way connector on the LCD (if used) and the wiring to the
front panel switches & controls and those switches & controls themselves.
3100
3101
3102
3103
3104
3105
3201
3210
3211
3212
3213
3214
3601
3602
3603
3608
3609
360A
360B
360C
360D
360E
Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
Low voltage warning Recharge batteries immediately
All 081x codes – Throttle wiring short or open circuits.
0816 and 0817 can be caused by incorrect
programming of the ISO test parameter
Memory corrupt Replace Controller if not cleared by disconnecting batteries for 1 min
All 070x codes -Wiring short circuit between Tiller Hi
and Lo Ref
Check for wiring short circuits on the 20 way connector on the Trio, the 16 way connector on the LCD (if used) and the
wiring to the front panel switches & controls and those switches & controls themselves.
Check for wiring short circuits or broken wires on the 20 way connector on the Trio, the 5 way connector on the LCD (if
used) and the wiring to the front panel speed / throttle control and the speed / throttle control itself.
All 150x codes - Check brake & wiring for open or
short circuit
Check the Traction motor connection on the Trio and check the wiring from this connector down to the Traction motor and
checking connections all the way. Otherwise possible fault in electro brake on traction motor or possible Controller fault.
All 310x codes - Probable short circuit of output
device or wiring - can sometimes cause permanent
Controller fault.
Check the Traction, Brush and Vac motor connections on the Trio and check the wiring from these connectors down to the
Traction, Brush and Vac motors checking connections all the way and also checking for short circuits. Check for wiring short
circuits or broken wires on the 14 way connector on the Trio and the wiring elsewhere on the machine. Otherwise replace
Controller.
Inhibit inputs - Exact usage dependent on
programming
Remove or correct what is causing the inhibit. Otherwise check for wiring short circuits or broken wires on the 20 way
connector on the Trio and the wiring elsewhere on the machine. Otherwise incorrect programming or operation of machine.
Possible Controller fault Replace Controller if not cleared by disconnecting batteries for 1 min
FORM 10004
1 OF 2
REVISED: 10/19/2005
DIAGNOSTIC CODES