Quonset Microwave QM1004-0.5-18 Скачать руководство пользователя страница 44

Страница: 44 / 105

QM1004-0.5-18 Combined RF Upconverter/Downconverter

User Manual

1.5 SYSTem Subsystem

Table 4.5:

SYSTem Subsystem Commands Summary

Command

Page

Description

SYSTem:BOOTstate

Specifies a state to boot to at device startup.

SYSTem:CURRent

Returns the current draw of the device.

SYSTem:ERRor

Returns error numbers and messages from the error
queue.

SYSTem:FIRMware

Returns the current firmware version of the device.

SYSTem:LOADstate

Loads and sets the parameters from the specified
state.

SYSTem:OPTions

Returns the configured options of the device.

SYSTem:READstate

Reads the parameters from the stored state without
changing the current device setup.

SYSTem:SAVEstate

Saves the current parameters to a specified state num-
ber.

SYSTem:SERialNUMber

Returns the serial number of the device.

SYSTem:USBPID

Returns the USB PID of the device.

SYSTem:VERSion

Returns the version of SCPI implemented in the Com-
bined RF Upconverter/Downconverter.

Quonset Microwave

Revision 1.2.1

Содержание QM1004-0.5-18










































































































Результаты поиска

Содержание QM1004-0.5-18

Отзывы:

Quonset Microwave QM1004-0.5-18, Руководство пользователя, Страница: 44 / 105

Результаты поиска

Содержание QM1004-0.5-18

Отзывы: