Quincy QP Series Скачать руководство пользователя страница 7

Страница: 7 / 44

QP Series

Quincy Compressor

2022201802, July 2014

3501 Wismann Lane, Quincy Ill. - 62305-3116

SECTION 2

SYSTEM DYNAMICS

Description & Application

Quincy Compressor QP Series compressors are heavy duty, air cooled, belt

driven compressors. The QP Series compressors are pressure lubricated and

capable of delivering 175 PSIG of compressed air.

Principles of Compression Cycles

Two Stage Compressors

During the downstroke of the piston of a two stage compressor, air is drawn

through an intake valve in the head of the compressor into the low pressure

cylinder and compressed during the upstroke of the piston.

The compressed air is then released through a discharge valve in the head

of the compressor to an intercooler (usually finned tub ing) where the heat

resulting from compression is allowed to dissipate. The cooler compressed air

is then drawn into a second compression cylinder, the high pressure cylinder,

for compression to final pressure.

From there the compressed air is released through a discharge valve to an

air receiver tank or directly to a network of compressed air supply lines. In

one revolution of the crankshaft a compression cycle is completed.

Principles of Lubrication Systems

Pressure Lubricated Compressors (QP Series)

Moving parts within the crankcase are supplied with lubrication by a positive

displacement, gerotor type oil pump. Oil is drawn up from the bottom of the

crankcase to the oil pump through an oil sump strainer screen. The oil is then

forced under pressure through the oil filter. Oil travels under pressure through

drilled journals in the crankshaft and connecting rods to lubricate crankshaft

bear ings, connecting rod journals, wrist pin bearings and the cylinder walls.

Principles of Cooling Systems

QP compressors are equipped with a compressor sheave with fan blades.

These fan blades force ambient air across cylinder head and intercooler fins

to cool the compressor. These compressors are designed to be operated with

the compressor sheave turning in a counterclockwise rotation (as viewed

“tummy to the sheave”).

Principles of Dryers & Filters

Moisture occurs naturally in air lines as a result of compression. Moisture

vapor in ambient air is concentrated when pressurized and condenses when

cooled in downstream air piping. Compressed air dryers reduce the moisture

vapor concentration and prevent water formation in compressed air lines.

Dryers are a recommended companion to filters, aftercoolers, and automatic

drains for improving the productivity of compressed air systems.

Содержание QP Series













































Результаты поиска

Содержание QP Series

Отзывы:

Похожие инструкции для QP Series

Бренды по названию

Популярные бренды

Quincy QP Series, Инструкция по эксплуатации

Результаты поиска

Содержание QP Series

Отзывы:

Похожие инструкции для QP Series

Бренды по названию

Популярные бренды