QuickLabel Systems QLS-4100X Скачать руководство пользователя страница 34

Страница: 34 / 118

QLS-4100 X

Press the SELECT key. The display will show the following prompt:

Press

and hold

the FORM FEED/ADVANCE key until the liner is inside the sensor

bracket. On notched media, temporarily slide the media out so that it is com-
pletely clear of the sensor assembly.

Press the SELECT key. The display will show the following prompt:

Press

and hold

the FORM FEED/ADVANCE key until the next label is inside the

Gap sensor.

Press the SELECT key. The display will show the following prompt:

Press

and hold

the FORM FEED/ADVANCE key until the next gap is positioned

behind the Media Sensor Assembly and in close proximity to the guide arrow
indicated on the center plate.

Press the SELECT key and observe the gap size on the display. The gap size
should be the same as the measured gap of your media and the following mes-
sage will be displayed:

Place Media @ Sensor
Then Press Select

Place Liner @ Sensor
Then Press Select

Place Gap @ Arrow
Then Press Select

Pause: Gap
Calibration OK

Содержание QLS-4100X























































































































Результаты поиска

Содержание QLS-4100X

Отзывы:

QuickLabel Systems QLS-4100X, Инструкция по эксплуатации и установке, Страница: 34 / 118

Результаты поиска

Содержание QLS-4100X

Отзывы: