QuickLabel Systems QLS-4100X Скачать руководство пользователя страница 105

Страница: 105 / 118

QLS-4100 X

105

Part Number

Description

14076-001

*Printhead

14039-001

*Drive Roll (black polyurethane)

14039-401

*Drive Roll (blue silicone)

14041-101

*Pinch Roller (aluminum with coating)

14039-101

*Platen Roller (black polyurethane, 60 Dur., bearings installed)

14039-501

*Platen Roller (blue silicone, 50 Dur., bearings installed)

14058-000

*Bearing Block Assembly (drive roll)

14057-201

*Lever Printhead Lift (4)

14057-301

*Lever Drive Roll Lift

23701-211

*Belt Timing 3mm 211T

24034-002

*Fuse 6.3 A (110VAC)

24034-004

*Fuse 4.0 A (220VAC)

13832-000

*Cleaning Pads (case of 50)

14050-400

Platen Shaft (4)

14050-050

Drive Shaft

14050-500

Drive Shaft Stub

RN1716

Drive Snap Ring (2)

14109-020

Collar (9)

14046-200

Shaft End Plate (5)

10609-016

#6 Pan Head Philips

25747-000

Motor Assy, Main

23682-114

Pulley, Drive

14099-000

Gas Spring, Drive Station

24878-000

Motor Assy, TTR (4)

12361-013

Slip Clutch, TTR (4)

26599-800

Sensor, Optical Encoder

14039-301

Roller, Optical Encoder

26599-100

Sensor, TTR / Head Up (9)

26599-600

Thru Sensor Probe

26599-000

Reflective Sensor Probe

26599-200

Sensor Amplifier Assy (2)

26599-700

Pressure Switch Assy

26588-100

Harness, Assy Printhead (4)

26599-300

Harness, Assy Motor

26599-400

Harness, Assy TTR Sensors

26599-500

Harness, Assy Head Up Sensors

42592-001

Controller, Assy PCB

42545-000

Power Supply, Assy PCB w/ Microstepper, Assy PCB IM483

25995-000

Microstepper, Assy PCB IM483 - only

42455-001

Keypad, Assy PCB

25459-200

Display, LCD w/ harness

24164-010

Cable, Parallel

24164-000

Cable, Serial

10787-001

Cord, Power

* Recommended Spare Parts

Parts specifications are subject to change without notice.

Contact QuickLabel Systems Technical Support to identify the correct parts and obtain current pricing.
Please have the serial number of your printer available.

Replacement Parts

Содержание QLS-4100X























































































































Результаты поиска

Содержание QLS-4100X

Отзывы:

QuickLabel Systems QLS-4100X, Инструкция по эксплуатации и установке, Страница: 105 / 118

Результаты поиска

Содержание QLS-4100X

Отзывы: