QuickLabel Systems QLS-4100X Скачать руководство пользователя страница 31

Страница: 31 / 118

QLS-4100 X

Thread the media through the Media Sensor Assembly and then through the
Media Travel Roller assembly.

Continue to thread the media through each of the print stations over the platen
rollers.

Finally, thread the media between the drive roller and pressure roller so that it
exits from the front of the printer.

Ensure that the media rests against each of the four Media Guide Rollers located
just behind the print stations on center plate.

Flip each Print Station Lift Lever lever clockwise to close the printheads.

Flip the Drive Roller Lift Lever counterclockwise to close the drive roller.

Reinstall the Media Guide Collar until it just rests against the outer edge of the
media.

Содержание QLS-4100X























































































































Результаты поиска

Содержание QLS-4100X

Отзывы:

Похожие инструкции для QLS-4100X

Бренды по названию

Популярные бренды

QuickLabel Systems QLS-4100X, Инструкция по эксплуатации и установке

Результаты поиска

Содержание QLS-4100X

Отзывы:

Похожие инструкции для QLS-4100X

Бренды по названию

Популярные бренды