background image

EN

DP2 L 770

QUICK 

DP2_L 770

 INSTALLATION AND USER’S MANUAL - REV000A

11

6 - Cautions & Use

6.2 - Troubleshooting

If the windlass stops and the hydraulic magnetic (or thermal magnetic*) switch has not tripped, wait a few seconds and try 

again (avoid keeping the button pressed).

If the hydraulic magnetic switch, has tripped, reset it and wait a few minutes before weighing anchor once again.

If, after a number of attempts, the windlass is still blocked, we suggest to move the boat to release the anchor.

7 - Maintenance

WARNING:

 make sure the electrical power to the motor is switched off when working manually on the windlass. 

Carefully remove the chain from the gypsy or the rope from the drum.

Quick® windlasses are made of materials resistant to the marine environment: it is essential, in any case, to periodically 

remove salt deposits that form on the external surfaces to avoid corrosion and consequently damage to the device.

Thoroughly wash the surfaces and parts where salt can deposit with fresh water.

Once a year, disassemble the gypsy and the drum according to the following sequence:

• Use the handle (1) to remove the gypsy cover (2)

• Remove the top clutch cone (3)

• Open the chain guide cover (7)

• Undo the retaining screws (5)

• Remove the gypsy (4)

• Remove the clutch washer (6)

Clean all the parts removed to avoid corrosion, and grease (with marine grease) the shaft thread and the gypsy where the 

clutch cones rest.

Remove any oxide deposits from the terminals of the electric motor and the reversing contactor unit; grease them.

If required, windlass must be disassembled by qualified personnel. 

Make sure that the gearmotor is cold before disassembling it.

The disposal must be carried out according to the regulations of the place where the work is carried out.

8 - Product disposal

As with installation, at the end of this product life, dismantling must be carried out by qualified personnel.

This product is made up of various materials, some can be recycled and others must be suitably disposed of; enquire about the 

recycling or disposal systems provided for by local regulations for this product category.

Some parts of the product may contain pollutants or hazardous substances that, if dispersed, may be harmful to the 

environment and human health.

As indicated by the symbol on the side, it is forbidden to dispose of this product as domestic waste. 

Separate the products for disposal in accordance with the regulations in force in your area or return the product 

to the seller when purchasing a new equivalent product. Local regulations may impose severe penalties for the 

improper disposal of this product.

Содержание DP2 L 770















Отзывы: