background image

 

 

T-

Stat LLC User’s Manual Rev 

3.2, 04/10/18 

Page | 5 

2.1 Installing the mounting plate 

1.

 

Plan the Location

 

The T-Stat should be mounted away from external sources of heat or cold 

(doors, HVAC supply grill, exhaust from equipment, radio heads, etc.) and provide a good 

representation of the shelter’s 

temperature. 

2.

 

Prepare the Area 

- The mounting screw holes will line up on a standard duplex outlet box or can 

be flush mounted to the wall.  When flush mounting, ensure clearance for the wires to exit 
through the center window on the back plate.  Install outlet box or screw anchors and run 
thermostat wires. 

3.

 

Remove the cover

 - The cover of the T-Stat is held on by four clips, two on the top and two on 

the bottom.  Remove the cover carefully, the cover may be snug and depressing the clips 
through the slot openings may help in getting the cover off. 

4.

 

Mount the Plate

 - Dress the wires through the center window on the back plate and install 

mounting screws.  Tighten screws to ensure the plate is mounted securely, but do not over 
tighten and warp the back plate. 

2.2 Wiring 

1.

 

Terminate the Wire Connections 

 Cut off excess wire, dress wire flush to the back panel and 

strip 1/4” of insulation to expose conductor.  Insert and tighten using the 

Wire Terminations 

diagram.  Label all point to point connections at both ends of the cable. 

2.

 

Connection Descriptions

Terminal 

Description 

 wire color 

HVAC 1 - R 

24VAC power - red 

HVAC 1 - C 

24VAC common - black 

HVAC 1 - G 

Fan Control 

 green 

HVAC 1 - Y 

Call for Cool - yellow 

HVAC 1 - W 

Call for Heat - white 

HVAC 2 - R 

24VAC power - red 

HVAC 2 - C 

24VAC common - black 

HVAC 2 - G 

Fan Control 

 green 

HVAC 2 - Y 

Call for Cool - yellow 

HVAC 2 - W 

Call for Heat - white 

Figure 2 - Connection Descriptions 

Содержание 100 T-Stat LLC










Отзывы: