Quectel M10 Скачать руководство пользователя

Страница: 93 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 92 -

- if TE character set other than "HEX" (refer CCSCS

in GSM 07.07): ME/TA converts GSM alphabet into

current TE character set according to rules of Annex A

- if TE character set is "HEX": ME/TA converts each 7-bit

character of GSM alphabet into two IRA character

long hexadecimal number

- if <dcs> indicates that 8-bit or UCS2 data coding scheme is

used: ME/TA converts each 8-bit octet into two IRA

character long hexadecimal number

<dcs>

depending on the Command or result code: GSM 03.38 SMS

Data Coding Scheme (default 0), or Cell Broadcast

Data Coding Scheme in integer format

<fo>

depending on the Command or result code: first octet of GSM

03.40 SMS-DELIVER, SMS-SUBMIT (default 17),

SMS-STATUS-REPORT, or SMS-COMMAND

(default 2) in integer format

<length>

integer type value indicating in the text mode (+CMGF=1)

the length of the message body <data> (or <cdata>)

in characters; or in PDU mode (+CMGF=0), the length

of the actual TP data unit in octets (i.e. the RP layer

SMSC address octets are not counted in the length)

<mid>

GSM 03.41 CBM Message Identifier in integer format

<oa>

GSM 03.40 TP-Originating-Address Address-Value field in

string format; BCD numbers (or GSM default alphabet

characters) are converted characters of the currently

selected TE character set (specified by +CSCS in TS

07.07); type of address given by <tooa>

<pdu>

In the case of SMS: GSM 04.11 SC address followed by

GSM 03.40 TPDU in hexadecimal format: ME/TA

converts each octet of TP data unit into two IRA

character long hexadecimal number (e.g. octet with

integer value 42 is presented to TE as two characters

2A (IRA 50 and 65)). In the case of CBS: GSM

03.41 TPDU in hexadecimal format.

pid

> GSM 03.40 TP-Protocol-Identifier in integer format (default

<sca>

GSM 04.11 RP SC address Address-Value field in string

format; BCD numbers (or GSM default alphabet

characters) are are converted to characters of the

currently selected TE character set (specified by

+CSCS in TS 07.07);; type of address given by

<tosca>

<scts>

GSM 03.40 TP-Service-Centre-Time-Stamp in time-string

format (refer <dt>)

Quectel

Содержание M10






































































































































































Результаты поиска

Содержание M10

Отзывы:

Похожие инструкции для M10

Бренды по названию

Популярные бренды

Quectel M10, Набор команд AT

Результаты поиска

Содержание M10

Отзывы:

Похожие инструкции для M10

Бренды по названию

Популярные бренды