Quectel M10 Скачать руководство пользователя страница 18

Страница: 18 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 17 -

active voice call, the first call will be automatically put on hold.

The current states of all calls can be easily checked at any time by

using the

AT+CLCC

Command.

2.2.4 ATD> <n> Originate Call To Phone Number In Current Memory

ATD><n> Originate Call To Phone Number In Current Memory

Response

This Command can be used to dial a phone number from current phonebook

memory.

Note: This Command may be aborted generally by receiving an

ATH

Command or a character during execution. The aborting is not possible

during some states of connection establishment such as handshaking.

If error is related to

functionality

+CME ERROR: <err>

If no dial tone and (parameter setting

ATX2

ATX4

)

NO DIALTONE

If busy and (parameter setting

ATX3

ATX4

)

BUSY

If a connection cannot be established

NO CARRIER

If connection successful and non-voice call.

CONNECT<text>

switches to data mode.

Note:

<text>

output only if

ATX<value>

parameter setting with the

<value>

When

returns to Command mode after call release

If successfully connected and voice call

Execution

Command

ATD><n> [;]

Parameter

<n>

Integer type memory location should be in the range of

locations available in the memory used

<;>

only required to set up voice call , return to Command state

Reference

V.25ter

Note

Parameter “I” and “i” only if no *# code is within the dial string

*# codes sent with

ATD

are treated as voice calls. Therefore, the

Command must be terminated with a semicolon “;”

See

ATX

Command for setting result code and call monitoring

Quectel

Содержание M10






































































































































































Результаты поиска

Содержание M10

Отзывы:

Бренды по названию

Популярные бренды

Quectel M10, Набор команд AT

Результаты поиска

Содержание M10

Отзывы:

Бренды по названию

Популярные бренды