Quectel M10 Скачать руководство пользователя

Страница: 54 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 53 -

see Write Command

Response

TA enables or disables the presentation of the CLI at the TE. It has no effect

on the execution of the supplementary service CLIP in the network.

If error is related to ME functionality:

+CME ERROR: <err>

Parameters

<n>

suppress unsolicited result codes

display unsolicited result codes

<m>

CLIP not provisioned

CLIP

provisioned

unknown

Write Command

AT+CLIP=[<n>]

Unsolicited result code

When the presentation of the CLI at the TE is enabled (and calling

subscriber allows), an unsolicited result code is returned after every RING

(or +CRING: <type>) at a mobile terminating call.

+CLIP: <number>, <type>,””,,<alphaId>,<CLI validity

Parameters

<number>

string type phone number of calling address in format

specified by <type>

<type>

type of address octet in integer format;

129 Unknown type(IDSN format number)

145 International number type(ISDN format )

<alphaId>

string type alphanumeric representation of <number>

corresponding to the entry found in phone book

<CLI validity>

0 CLI valid

1 CLI has been withheld by the originator

2 CLI is not available due to interworking problems or

limitations of originating network

Reference

Note

3.2.21 AT+CLIR Calling Line Identification Restriction

AT+CLIR Calling Line Identification Restriction

Read Command

AT+CLIR?

Response

+CLIR:

<n>, <m>

If error is related to ME functionality:

+CME ERROR: <err>

Quectel

Содержание M10






































































































































































Результаты поиска

Содержание M10

Отзывы:

Похожие инструкции для M10

Бренды по названию

Популярные бренды

Quectel M10, Набор команд AT

Результаты поиска

Содержание M10

Отзывы:

Похожие инструкции для M10

Бренды по названию

Популярные бренды