Quato iColor Display 3.7 Скачать руководство пользователя страница 16

Страница: 16 / 73

Software installation for Intelli Proof displays for
Mac OS X

Please insert the CD and open the Disk Image
(.dmg). Copy the iColor Display folder to your hard-
disk.

The Version 3.8.x.x or newer of iColor Display does
not need a driver for the Intelli Proof calibration
interface.

If a driver from an earlier version is installed please
unistall this driver as below:

please remove the following entries from directory
MacintoshHD:\System\Libary\Extensions
SilabsUSBDriver.kext
SilabsUSBDriver64.kext

After removing a restart of your system is requiered.

You can check the status of the device with the Apple
System Profiler (About...-> more Info). The USB-Inter-
face shows up as „CP210x“ (Calibration Processor).

The measurement devices can be connected to your
Mac without installing a driver. iColor Display inclu-
des all necessary device frameworks.

Only for the Basiccolor Discus measurement device
a driver is necessary. It could be found in the iColor
Display.dmg, folder Drivers.

Notice:

You need administrator rights to install the

driver. Saving profile in the ColorSync folder also
needs administrator rights.

Notice:

If you have only obtained the iColor Display

Software without Display, skip the installation of the
hardware and just proceed to the introduction of the
software.

Содержание iColor Display 3.7










































































Результаты поиска

Содержание iColor Display 3.7

Отзывы:

Похожие инструкции для iColor Display 3.7

Бренды по названию

Популярные бренды

Quato iColor Display 3.7, Руководство пользователя

Результаты поиска

Содержание iColor Display 3.7

Отзывы:

Похожие инструкции для iColor Display 3.7

Бренды по названию

Популярные бренды