manualshive.com logo in svg

Quantum QT-740, Руководство по обслуживанию

Поделиться
Скачать
Quantum QT-740 Скачать руководство пользователя страница 47

 

Chapter 4  Service Instructions

Models QT-740 & QT-750 - Service Manual

41

13. Re-install Belt Tensioner (if removed).  Adjust belt tension as fol-

lows:
a. If not already done so, loosen nut on Belt Tensioner.
b. Increase belt tension by adjusting Belt Tensioner downward.  

The belt is properly tensioned when, at the midpoint of the 

longest belt span, there is approximately 1/4" deflection.

c. When belt tension is set, tighten nut on Belt Tensioner.

14. Verify Sync Belt Safety Switch is in open position (if not, motor 

will not operate).  Adjust switch height if necessary.

15. Remove Safety Bracket.
16. Reinstall upper and lower table covers (refer to Chapter 2, 

Assembly and Installation).

17. Turn on power.  Perform an operational test and check table 

travel and positions.

BALL SCREW 
MOUNTING 
BLOCK

CENTER 
BALL SCREW  
MOUNTING 
BLOCKS

BALL NUT 
BLOCKS

Figure 19.  Ball Nut and Screw Mounting Block Locations

Содержание QT-740

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды